Answered: 8. For the beam and loading shown,…

8. For the beam and loading shown, determine the reaction at the roller support. The beam is W250X25.3 with load density at B of 2kN/m with L=9m and E=180GPa A Wo B 000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: Problem II. The truss shown in the figure below is applied with force P (refer to the table of…

Q: For the beam shown below, Find the bending stress at point A. 50 kN 1.3 m. 120 a 22 22 20 3 m 3 m

A: Given that:

Q: Situation 9: A beam is loaded as shown in the figure. Its cross-sectional properties are also given.…

Q: Problem 2: A rigid block of negligible mass is supported by three symmetrically spaced rods as…

A: The stress in the copper bar is σc=70 MPa. The stress in the steel bar is σs=140 MPa. The area of…

Q: 7.4 J The courthouse record for a 1902 property survey at Ketchikan, Alaska, lists the magnetic…

A: Given:- The magnetic direction of a property boundary = S 82°44' W The declination of the property =…

Q: Figure 1 shows a pin-connected truss system with pin supports at points A and B. Member AC has an…

A: First of all calculate the forces in member in terms of F Then calculate the stress in members…

Q: Determine: The shear diagram The moment diagram The value of the maximum bending moment The maximum…

A: Given: A simply supported overhang beam consisting of uniformly varying load and point load. To…

Q: Structural Analysis II (Please use the consistent deformation method)

A: Data given Find: reaction and axial forces by consistent deformation method

Q: A tied column 350 mm x 600 mm in cross section is reinforced with 6-28 mm Ø bars arranged as shown…

A: Answer (1) Calculation of the total compressive force of the steel reinforcement Total compressive…

Q: Two chords AB and BC are joined at B and support a load W as shown in Figure 3.3 -8. 30 45° Figure…

Q: Three rods, each of area 250 mm2, jointly support a 7.5 kN load, as shown in Figure below. Find the…

Concept explainers

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.

Question

8. For the beam and loading shown,
determine the reaction at the roller support.
The beam is W250X25.3 with load density at
B of 2kN/m with L=9m and E=180GPa
A
-L
Wo

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Solution:

VIEW

Step 3: Calculation of support reactions:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

plz determine it ASAP.
2. Determine the internal forces and draw the diagrams
The beam has a rectangular cross section and is subjected to the loadings shown in Figure 1. Determine the principal stresses at point A and point B, which are located just to the left of the 15-kN load. Show the results on elements located at these points and its orientation angle.
For the beam shown: 1. Draw the free-body diagram (FBD) and determine the reactions at the supports. 2. Determine the internal forces and draw their diagrams. 3. Design the beam using IPE shape. 4. Draw the stress diagram in the critical cross section. Data: F= 60 kNm, L = 1 m, 0 = 120 MPa. I IPE A F L #C L B
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
A simply supported beam is loaded by the couple M=2000 N-m as shown. The beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm 3 m -2m1 10.5 cm BI 12 cm M. Determine the maximum tensile stress in the beam. O 1.60 MPa 3.73 MPa )2.49 MPa O1.07 MPa Determine the maximum compressive stress in the beam. 3.73 MPa O 1.07 MPa 2.49 MPa O 1.60 MPa Determine the maximum shear stress in the beam. O 00588 MPa 0.0490 MPa 0.0653 MPa O 0.0667 MPa
3
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
Asap
Q.3)A rigid bar DAB is supported by two circular rods and a pin as shown below. The member at D is an aluminum (E = 70 GPa) rod, and the member BC is a steel (E = 200 GPa) rod. The diameter of the aluminum rod is 10 mm and that of the steel rod is 5 mm. Calculate the average normal stresses in the steel and aluminum rods due to the applied load of 650 N. Also, determine the rotation of the rigid bar DAB about the pin A, and the horizontal displacement of point D. 200 mm A B 150 mm 100 mm 150 mm 650 N DI 50 mm
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. L. C D VAR 2m +12m -1.2 m-1.2 m 1.2 m-