750 mm 750 mm B. 5 kN 500 mm

Q: respectively. The tank has an inner diameter of 4 m. The thickness of the cylindrical are made from…

A: A scalar quantity in when when an amount of force act on the object in a cross section area, that is…

Q: The internal loadings at a cross section through the shaft consist of an axial force of 1500 kN, a…

A: Given: axial force, P =1500KN Bending moment, M =40KNm Torsional moment, T =40KNm radius of shaft,r…

Q: A stainless-steel thick-walled cylinder with inner and outer radii (b and a) of 225 mm and 350 mm,…

A:

Q: A steel penstock has a 750-mm outer diameter, a 12-mm wall thick-ness, and connects a reservoir at A…

A: Given data: Outer diameter of penstock, d0 = 750 mm Thickness of the penstock, t = 12 mm Density of…

Q: The forces ar applied to the bar shown. Determine the normal and shearing stresses at (a) point a,…

A:

Q: A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in.…

A:

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: The storage tank shown contains liquefied propane under a pressure of 1.4 MPa at a temperature of 38…

A:

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

A:

Q: A pressurized spherical tank is made of 0.5-in.-thick steel. If it is subjected to an internal…

A: Given: The internal pressure in the tank is p=200 psi. The thickness of the spherical tank is t=0.5…

Q: A pressurized steel tank has inner radius r = 0.5 m and wall thickness t = 20 mm. The steel has…

A: Given data: Before proceeding with the solution check whether it is a thin or thick pressure…

Q: A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of…

A: Given: The internal pressure in the tank is p=300 kPa. The inner radius of the spherical tank is ri…

Q: A force Q of magnitude 3kips is applied on the machine element AB of uniform thickness 0.8.…

A: Given, Q=3 kips The thickness, t=0.8 in

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the…

A: Allowable normal stress = 120 Mpa Allowable shear stress = 60 Mpa Answer : (a) 8.39 N

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

A:

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: Determine the maximum shear stress If maximum principal stress=50 MPa, Minimum principal Stress=20…

A:

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: 9. The compressed air vessel has a radius of 42 cm and a uniform wall thickness of 5 82 cm mm.…

A:

Q: The assembly consists of a solid 15 mm diameter rod connected to the inside of a tube using a rigid…

A:

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 49 ft. The…

A: To find: The maximum normal stress and maximum shear stress. Given: The height of water in the tank…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A: Given Data The load acting at A is PA=80 kN. The load acting at B is PB=280 kN.  The ultimate…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 380 lb. Dimensions…

A:

Q: Determine the normal stress in a ball, which has an outside diameter of 180 mm and a wall thickness…

A: As per given question  Gage pressure =66mpa Wall thickness =4.6 mm Outside diameter =180 mm We have…

Q: 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000…

A:

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 39 ft. The…

A: According to the given dataDensity=We need to find The maximum normal stress and The maximum shear…

Q: The extruded plastic shape will be subjected to an internal shear force of V= 380 Ib. Dimensions of…

A:

Q: The compressed air vessel has a radius of 42 cm and a uniform wall thickness of 5 82 cm mm. Knowing…

A:

Q: The tank shown is fabricated from steel plate. Determine the required thickness of plate which maybe…

A: transverse stress = longitudinal stress =  σl = 40 MPa = 40 * 106 N/m2 internal pressure = P = 1.5…

Q: A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in…

A: Outer diameter, D = 300 mm  Wall thickness, t = 3 mm  Inner diameter, d = D - 2t = 300 - (2*3)  d =…

Q: A spherical gas tank has an inner radius of 6.1 m. If it is subjected to an internal pressure of 445…

A:

Q: Determine the principal planes and the principal stresses for the state of plane stress resulting…

A:

Q: A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously…

A: Given: external diameter = 0.5 m internal diameter = 0.4 m internal pressure = 25 MN/m2 hoop stress…

Q: A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having…

A: Load developed(P) in the cable is given by:→P=∆L×AELwhere∆L=extension/deformation in cableL=Length…

Q: The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to…

A: Step 1:Step 2: Step 3: Step 4:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.