7.77 A spherical, underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of 85 mm and dissipates 300 W. (a) Estimate the surface temperature of the pod when suspended in a bay where the current is 1 m/s and the water temperature is 15°C. (b) Inadvertently, the pod is hauled out of the water and suspended in ambient air without deactivating the power. Estimate the surface temperature of the pod if the air temperature is 15°C and the wind speed is 3 m/s.

7.77 A spherical, underwater instrument pod used to make soundings and to measure conditions in the water has a diameter of 85 mm and dissipates 300 W. (a) Estimate the surface temperature of the pod when suspended in a bay where the current is 1 m/s and the water temperature is 15°C. (b) Inadvertently, the pod is hauled out of the water and suspended in ambient air without deactivating the power. Estimate the surface temperature of the pod if the air temperature is 15°C and the wind speed is 3 m/s.

Name: 7.77 A spherical, underwater instrument pod used to makesoundings and
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 7.77 A spherical, underwater instrument pod used to makesoundings and to measure conditions in the water has adiameter of 85 mm and dissipates 300 W.(a) Estimate the surface temperature of the pod whensuspended in a bay where the current is 1 m/s an

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A velocity of the cylindrical particles of diameter and length are 0.3 mm. It is drop in the air tube .The density of the particle is 1200 kg/m³. The initial velocity of the particle is zero. Air conditions are 28 °C and 1 atm. The viscosity of air is 1.8 x 105 kg/m-s, and superficial velocity of air is 11 m/s. The Reynolds number range is between 1100 and 900. (a) Derive an equation of the velocity of the particles with neglect wall effects. (b) How long of distance if the velocity become steady state filling?
An oil preheater consists of a single tube of 10-mm diameter and 5-m length, with its surface maintained at 180°C by swirling combustion gases. The engine oil (new) enters at 70°C. What flow rate, in kg/h, must be supplied to maintain an oil outlet temperatur of 105°C? What is the corresponding heat transfer rate, in W? m = kg/h W
Nutrient media is flowing at a rate of 1.5 L min in a tube that is 5 mm in diameter. The walls of the tube are covered with antibody-producing cells, and these cells are anchored to the tube wall by their interaction with a special coating material that was applied to the surface of the tube. If one of these cells has a surface area of 500 um², what is the amount of force that each cell must resist as a result of the flow of this fluid in the tube? Assume the viscosity of the nutrient media is 1.2 cP=0.0012 Pa sec.
Question- In a laminar flow between two parallel plates with a separation distance of 6 mm, the centre line velocity is 1.8 m/s. The velocity (in m/s) at a distance of 1 mm from the Boundary is
what is the unit of the medium resistance and the specific cake resistance
Questions: 1. Explain the physical meaning and equation of Reynolds number, Nusselt number, Biot number, Prandtl number ?
Question 9 Consider the flow of water over a flat plate. In a different experiment consider the flow of air over a flat plate. In both cases the flow is steady, the boundary layers that are formed are laminar and the gravitational acceleration can be neglected. In both cases the velocity far from the plates is the same (v.) and the temperature is also the same (80 °F). For the same distance x from the leading edge, in which boundary layer will the friction coefficient be higher? (a) The friction coefficient is the same for both cases. (b) In water. (c) In air. (d) It depends on the velocity profile that is assumed inside the boundary layer.
Atmospheric air with a temperature of 300 K flows on both sides of a thin, rectangular, flat plate that is maintained at 600 K. The plate is 150 mm long and 75 mm wide. The free stream velocity is 2.5 m/s; plate's length is in the direction of air flow. Draw a labeled sketch and determine: a) The drag force acting on the plate. b) The rate of heat loss from the plate.
a. What units must the constant 0.644 have?b. What should be the value of the constant when all units areconverted to English units (masses in lbm, lengths in ft, temperatures in oR,times in h, energies in Btu)? answer asap please
Air stream at 27 degrees * C is moving at 0.3 m/s across a 100 W electric bulb at 127 degrees * C. If the bulb is approximated by a 60 mm diameter sphere, estimate the heat transfer rate and the percentage of power lost due to convection.
A 0.407m long vertical steel plate at a surface temperature of 700K is in contact with hot air at 237K, latm absolute pressure. If E=0.81 for steel pipe:a. Calculate the total 1S1 transfer coefficient for the convection increase 1 convectionb. What is the heat loss per unit area of the surface?