Please Solve both parts. !Required informationA smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s.What is the sphere diameter if it is encountering transition to turbulence, Red=250,000?0008 m !Required informationA smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s.What is the sphere diameter (in micrometer) if it is encountering creeping motion, Red=1?0032051 μm

Answered: Image /qna-images/answer/59f22296-bd95-42ea-ac27-29c10724aa6f.jpg

! Required information A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s. What is the sphere diameter (in micrometer) if it is encountering creeping motion, Red=1? 0032051 μm

! Required information A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s. What is the sphere diameter (in micrometer) if it is encountering creeping motion, Red=1? 0032051 μm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.6P: 5.6 A fluid flows at 5 over a wide, flat plate 15 cm long. For each from the following list,...

See similar textbooks

Related questions

Q: The following graph shows a load-extension graph from a test on a polymer specimen 15mm in diameter…

A: The diameter is The length is

Q: 6. In a plane stress condition, the components of stress at a point are o, =20 MPa, oy =80 MPa and…

Q: A body at a temperature of 50 deg. F is placed outdoors where the temperature is 100 deg. F. If…

Q: A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain…

A: Given:The diameter of the thread, The value of the load, The mean diameter of the thrust collar, The…

Q: A steel ball weighing 2 lb is dropped from a height of 3000 ft with no velocity. As it falls, the…

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

Q: now opened, and one-half of the total mass is withdrawn from the tank in liquid form. Heat is…

A: Given: The volume of a tank is, V=0.6 m3. The temperature of water is, T=170°C=443.15 K. The…

Q: A bacteria culture is known to grow at a rate proportional to the amount present. After one hour,…

A: Given question belongs to the Basics of engineering.

Q: Determine the maximum shear stress in the shaft (Figure 1). Given the torsional shear stress is 45…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Required information The helium-filled balloon in the image is tethered at 20°C and 1 atm with a…

A: Given Temperature T= 20 0c String is negligible mass and drag diameter of the balloon d =58 cm =0.58…

Q: Wo spaces. B 15 f B 6 k 20 k

A: Both problems are solved below.

Q: For the following control system: K r(t) s(s+2) y(t) s+6 (a) Find the closed loop transfer function…

Q: Mark Billiards. Consider two #identical billiard balls (I = mR²) with mass 0.160 [kg] and radius…

Q: A thin semi-circular pipe has been bent in the shape of a semicircle of radius R and is held fixed.…

A: Draw the free body diagram of the of the given arrangement: Note from the figure: θ=x2R=x2R

Q: Figure 2 shows a ballistic pendulum consists of 5 kg slender rod and 10 kg solid cylinder. The…

Q: A thin uniform semicircular plate of radius R and mass m (link 1) is hinged at A and B to a clevis…

Q: Based on the given structure, calculate: i) The resultant force. The direction (angle) of the…

Q: 5275 is a commonly used grade of steel For this grade, the ultimate tensile strength fy=? Select…

A: Answer For First:- According to standard for mild steel code S275 Composition: Carbon 0.25%…

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: 1. For the beam below determine bending moment 3' to the right from support A. 10K W-1k/ft 8K A R 3'…

A: drawing the free body diagram

Q: QUESTION 21 Smaller dirt particles are removed from the air by the filter's O deflector O baffle…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: For each of the following models, obtaln the free response and the time constant, If any. The model…

A: GIVEN : 16x'+14x=0.........eq(1) , x(0)=5 we know that Lx' =sX(s) -x(0) L(x) = X(s)

Q: The pressure at a point on the wing of an airplane is 75.8kPa. The airplane isying with a velocity…

A: Solution is given below:

Q: Air having a density of 1.27 kg/m³ enters the inlet of an engine at a rate of 1000 m³/sec of a…

Q: Member ABC is controlled using a rack and pinion, which is connected at B. (The rack is the long,…

Q: 3 ft 5 ft A 1 of 1 > aA ▼ Determine the magnitude of the acceleration of point B at this instant.…

Q: A single-acting, two-stage air compressor with perfect intercooling delivers 15 kg/min of air at 25…

A: Given That, X=2 two stages,n=1.25, m=15 kg/min,p3=25 bar, p1=1 barT1=15°C=15+273=288 K,n=1.25…

Q: In a thermal power plant, an adiabatic steam turbine operating at steady state with inlet conditions…

A: Given:P1=30 barT1=350°Cm=10 Kg/sP2=5 barT2=200°CP3=0.15 barx3=0.9T∞=25°C NOTE: According to…

Q: The surface of of a flat plate of dimenstions 1 mx 2 m is maintained at a temperature of 38°C in a…

Q: Problem II. A right circular cone is 100mm in diameter and 200mm high and weighs 1.6N in air. How…

A: Given: Weight of the right circular cone→W=1.6 N Diameter of the cone→D=100 mm=0.10 m Height of the…

Q: Consider the truss shown in (Eigure 1). Suppose that F₁ = 40 kN and F₂= 25 KN. Figure 50 KN -2m-2m-…

Q: A strain gage located at C on the surface of bone AB indicates that the average normal stress in the…

Q: Part A As shown, a force vector F with a magnitude of c = 26.0 lb is applied at point A and is…

A: As the figure for part 2 is not given so solved part 1. Given-Information:- a = 9.50 ftb = 3 ftc =…

Q: The amusement park ride consists of a 200-kg car and passenger that are traveling at 4.6 m/s along a…

A: Find the speed of car when t = 4 sec and work done.

Q: A tank initially holds 10 gal of fresh water. at t=0, a brine solution containing 1/2 lb of salt per…

Q: 11) 1. Tank A has 100 units of water. 2. Tank B has 20 units of water. 3. Tank A transfers 5 units…

A: GivenHA=100 unitsVAB=5 units/minHB=20 unitsVBC=2 units/min

Q: Air at 30°C Dry-bulb temperature, 40% RH enters a heating chamber at the rate of 500 cmh (cu.m/hr).…

Question

Please Solve both parts.

!
Required information
A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s.
What is the sphere diameter if it is encountering transition to turbulence, Red=250,000?
0008 m

!
Required information
A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 3 cm/s.
What is the sphere diameter (in micrometer) if it is encountering creeping motion, Red=1?
0032051 μm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please correct answer
QI/ If the velocity profile of the boundary layer is :O find the thickness of boundary layer, the shear stress at trailing edge and the drag force on one side of plate 2 m long, if it is immersed in water flowing with velocity of 0.4 m/s (p 998 D = 1.007*10-6 m2/s %3D
A solid sphere having diameter 5 mm is falling through oil of density 800 kg/m? and dynamic viscosity 0.8 kg/m-s at a constant velocity of 1 cm/s. Drag force on the sphere
solve the question given in image completely.
(b) In two dimensional boundary layer, shear stress was changed linearly from the solid surface toward y-axis until it reach the value of zero at y = 6. Based on Table 2 and setting given to you; () Derive the equation of displacement thickness and momentum thickness using Von Karman Approximation Method ; and (ii) Determine the accuracy of this method in determining the value of displacement thickness and momentum thickness. Table 2 : Equation of Velocity Profile Setting Equation wU = 3(y/8)/2 – (y/8j?/2
(b) In two-dimensional boundary layer, shear stress was changed linearly from the solid surface toward y-axis until it reaches the value of zero at y = 8. Based on Table 2 and setting given to you; (i) Derive the equation of displacement thickness and momentum thickness using Von Karman Approximation Method; and (ii) Determine the accuracy of this method in determining the value of displacement thickness and momentum thickness. Table 2: Equation of Velocity Profile Equation u/U = 3(y/8)/2 – (y/8)³/2 Setting 2
Please help
fluid mechanics subject! please help me solve this thankyou very much!
Air at 20 °C forms a boundary layer near a solid wall, in which the velocity profile is sinusoidal (see Fig. 1-14). The boundary-layer thickness is 7 mm and the peak velocity is 9 m/s. Compute the shear stress in the boundary layer at y equal to (a) 0, (b) 3.5 mm, and (c) 7 mm. 7 mm Vmax = 9 m/s Peak Sine wave Fig. 1-14
A fluid with viscosity of u = 1.752 x 10-5kg/m. s and density of p = 1.2kg/m3 flows at U=1 m/s over a flat plate. The boundary layer displacement thickness %3D at the end of the plate is reported 0.01315 m. Assuming the flow is laminar, (a) Find the boundary layer thickness at the end of the plate. (b) Find the momentum thickness at that location. (c) Find the drag force of the plate.
A cylindrical steel tank is 6 m in diameter and 9m high at -15°C is completely full of gasoline. If the temperature increases to 22 °C. Taking into account the expansion of the tank itself, how much gasoline will overflow? [11.0m3]
A solid aluminum disk (SG = 2.7) is 2 in in diameter and3/16 in thick. It slides steadily down a 14 8 incline that iscoated with castor oil (SG = 0.96) film one-hundredth ofan inch thick. The steady slide velocity is 2 cm/s. UsingFigure A.1 and a linear oil velocity profile assumption,estimate the temperature of the castor oil.