KNOWN: Velocity and temperature profiles for laminar flow in a parallel plate channel. FIND: Mean velocity, um, and mean (or bulk) temperature, Tm, at this axial position. Plot the velocity and temperature distributions. Comment on whether values of um and Tm appear reasonable. SCHEMATIC: y Уо u(yly), T(yly) Fluid 0 ASSUMPTIONS: (1) Laminar incompressible flow, (2) Constant properties.

KNOWN: Velocity and temperature profiles for laminar flow in a parallel plate channel. FIND: Mean velocity, um, and mean (or bulk) temperature, Tm, at this axial position. Plot the velocity and temperature distributions. Comment on whether values of um and Tm appear reasonable. SCHEMATIC: y Уо u(yly), T(yly) Fluid 0 ASSUMPTIONS: (1) Laminar incompressible flow, (2) Constant properties.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.6P: 5.6 A fluid flows at 5 over a wide, flat plate 15 cm long. For each from the following list,...

See similar textbooks

Similar questions

Solve part a. in Matlban with the following changes please: Flow Speed U_inf = 0.5 m/s Plate Surface Temperate Ts = 77 C Describe what each case represents in terms of the boundry layer
Problem 4 Viscous heating in slit flow. Find the temperature profile for the viscous heating problem solved in class, when given the following boundary conditions: at y = 0, T = To; at y = b, qy=0. VD To
Cooling water for a power plant is stored in a pond 900 m in length and 400 m wide. A dry wind at 300 K blows in a horizontal direction parallel to the 900 m side of the pond at a velocity of 2 m/s. The cooling water is at 300 K. Known the air dynamic viscosity v= 1.67 x10m?/s.; the Re transition from laminar flow to turbulent flow is 500,000; and the saturated water vapor pressure at 300 K is 3580 Pa; gas constant R= 8.3144 J/mole.K. 1.) At what position across the pond is the air flow no longer laminar? Would it reasonable to assume that the mean gas-film mass transfer coefficient for water vapor in air is dominated by turbulent flow mass transfer? 2.) As part of an engineering analysis to predict the evaporation rate of water from the pond, determine the mean gas film mass transfer co-efficient. 3.) Calculate the rate of water evaporation from the pond.
Question describe in picture
* ZAIN IQ liı. SuspendEA IN A ROom, Ana TS Subjected To Air Flow Parallel To I... A 2m by 3m flat plate is suspended in a room, and is subjected to air flow parallel to its surfaces along its 3m long side as shown in the figure. The free stream air temperature, T, is 20°C and the velocity is 7 m/s. The total drag force acting on the plate is measured to be 0.86 N. Determine the average convection heat transfer coefficient for the plate. Air 20°C, 7 m/s L= 3 m. This problem has been solved! See the answer
Consider an airflow over the surface of a flat plate with a temperature Ts = 250 °C. At some distance from y the origin, the temperature profile of the airflow is given by the following function: q/A As, Ts T(y) = T, -(T. -T3)exp -u. y a fluido dAs The airflow at atmospheric pressure has a free flow velocity u.. = 0.06 m/s and a temperature T = 15°C. The thermal diffusivity of the fluid is aluid = 3.872E-05 m?/s and its thermal conductivity Afluid = 0.03383 W/(m K). 1. Determine the heat flux over the surface of the plate. q/A = W/m? 2. Determine the convection coefficient of the airflow. h = W/(m² K)
Consider an airflow over the surface of a flat plate with a temperature Ts = 220 °C. At a certain point from the origin, the temperature profile of the airflow is given by the following y function: q/A As, Ts dA, T(y) = T, - (T. - T)exp afuido The airflow at atmospheric pressure has a free flow velocity u = 0,08 m/s and a temperature T, = 20°C. The thermal diffusivity of the fluid is afluid = 3,65E-05 m?/s and its fluid thermal conductivity Aquid = 0,0329 W/(m K). For the position that corresponds to the temperature profile above, 1. Determine the heat flux over the surface of the plate. 2. Determine the convection coefficient of the airflow.
An approximation for the boundary-layer shape in is the formula u(y) - U sin 0 sys d where U is the stream velocity far from the wall and d is the boundary layer thickness, as in Fig. If the fluid is helium at 20°C and 1 atm, and if U = 10.8 m/s and 8= 3 cm, use the formula to (a) estimate the wall shear stress Tw in Pa, and (b) find the position in the boundary layer where t is one-half of Tw. -- y = 6 u(y)
Question 1: Consider fully developed two-dimensional Poiseuille flow: flow between two infinite parallel plates separated by distance h, with both the top plate and bottom plate stationary, and a forced pressure gradient dP/dx driving the flow as illustrated in the figure (dP/dx is constant and negative). The flow is steady, incompressible, and two-dimensional in the xy-plane. The velocity components are given by 1 dP u(y) u = 2μ dx (y²hy); v = 0 where is the fluid's viscosity. Is this flow rotational or irrotational? a. If it is rotational, calculate the vorticity component in the z-direction. Do fluid particles in this flow rotate clockwise or counterclockwise? b. calculate the linear strain rates in the x- and y-directions, and c. calculate the shear strain rate ɛxy. d. Combine your results to form the two-dimensional strain rate tensor εij in the xy-plane,
A flat plate of length equal to 50 cm is parallel to a 25 m/s stream velocity. What is the shear stress, in Pa, at a section 40 cm away from the leading edge of the plate? The fluid is air with density equal to 1.2 kg/m³ and kinematic viscosity of 1.5 x 10-5 m²/s. Answer:
1. In flow over a surface, velocity and temperature profiles are of the forms u(y)=Ay+By²-Cy³ and T(y)=D+Ey+Fy²+Gy³ where the coefficients A through G are constants. Obtain expressions for the friction coefficient Cf and the convection coefficient h in terms of u∞, T∞, and appropriate profile coefficients and fluid properties. Answer: h= -k[E D To
please help to my question