7.42 A water discharge of 8 m³/s is to flow through this hori- zontal pipe, which is 1 m in diameter. If the head loss is given as 7V²/2g (V is velocity in the pipe), how much power will have to be supplied to the flow by the pump to produce this dis- charge? Assume a = 1.0 at all locations. Elevation = 40 m Water Pump 1 m - Elevation = 20 m Elevation 10 m 300 m - 300 m PROBLEM 7.42

7.42 A water discharge of 8 m³/s is to flow through this hori- zontal pipe, which is 1 m in diameter. If the head loss is given as 7V²/2g (V is velocity in the pipe), how much power will have to be supplied to the flow by the pump to produce this dis- charge? Assume a = 1.0 at all locations. Elevation = 40 m Water Pump 1 m - Elevation = 20 m Elevation 10 m 300 m - 300 m PROBLEM 7.42

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The oil tank for the hydraulic system of figure below is air-pressurized at 10 psig. The inlet line to the pump is 10 ft below the oil level while point 3 is 2ft below pump inlet. The pump flow-rate is 30 gpm and has a power equal to 0.5 HP. Find the pressure at station 3 if there is a 28 ft head loss between station 1 and 3.
please
Provide the diagram for the problem. Choose the correct answer and provide complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. A. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? a. 86%b. 65%c. 77%d. 50% B. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe. a. 45 lb/sb. 37 lb/sc. 52 lb/sd. 29 lb/s
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The then breaks into N narrow Pipes (which have a diameter, d2, and a length, L2), before the water is released to the atmosphere, as shown in the figure. The entrance to the small pipe from the large pipe has a loss coefficient of KL. You may assume the flow is laminar and fully developed everywhere in the system, and that any changes in height are neglible. (The viscosity is NOT negligible) a) Find an expressin for the velocity of water leaving the sprinkler b) Find an Expression for the gauge pressure at point A, a distance L1 upstream of the narrow pipes. Express your answer in terms of the flowrate, Q. c) The inner diameter of the first segment of the pipe is d1 = 10mm, the inner diameter of the second set of pipes is d2 = 1mm, with N = 25. The flowrate through the sprinkler is Q = 0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds…
Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs. machine a pump or a turbine? pressures at points A and B? losses. Pump 1. The discharge in the siphon is 2.80 cfs, D = 10 in., L1 = 3 ft, and L2 = 3 ft. Determine the head loss between the reservoir surface and point C. Determine the pressure at point B if three-quarters of the head loss (as found above) occurs between the reservoir surface and point B. 1 m REVIEW Home Work (1) Energy Equation Water T = 10ºC REPPER Water Same elevation Machine Elevation = 40 m -Elevation = 20 m Elevation 10 m 300 m + -300 m- 4. Assume that the head loss in the pipe is given by hL = 0.014(L/D)(V2/2g), where L is the length of pipe and AZ₂ AFL B Elevation 100 m L = 100 m D = 60 cm Water T= 10°C 3. A water discharge of 10 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7V2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow…
A pipe with a diameter of 2cm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 2ms, what is the velocity of the flow at the nozzle when it is adjusted to have a diameter of 4mm?
The air is measured at 20 deg. C and 533mm Hg. The duct diameter is 622 mm while the discharge diameter is 385mm The fan draws 2 m^3/s air and the static pressure measured is 8 cm water Determine the power output in kW ndmal places
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
The pressure after the pump in a 6-inch inside smooth pipe conducting water is 20 psia. The water is dischargedat an open tank 100ft. from the pump. Calculate the rate of discharge of water in ft^3/s
A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve
4. Water (p = 1000 kg/m³) is transferred from a large lake to an open storage tank located at elevation as shown in the Figure 2 below at a flowrate of 90m³/hr. The losses through pipe and fittings (hL) is given as 8m. Determine the mechanical efficiency of the pump if the shaft power required is 12kW. State the assumptions made in your calculations. 30 m WaterLevel Pump Centre Figure 2 Tank