*7-48. The joint is subjected to the axial member force of27 kN. Determine the average normal stress acting onsections AB and BC. Assume the member is smooth and is40 mm. thick.27 kN6020

Given data: Length of section AB, LAB = 40 mm. Length of section BC, LBC = 112 mm. The thickness of…

Answered: *7-48. The joint is subjected to the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed loading along its length which is 0 at x= 0 and 9 kN/m at x= 1.5 , and to two concetrated loads Determine the average normal stress in the bar as a function of x for 0 <_x < 0.6m
13-50. The C-frame is used in a riveting machine. If the force at the ram on the clamp at Dis P -8 kN, sketch the stress distribution acting over the section a-a. -200 mm- 10 mm 60 mm -10 mm
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.
7-63. The cotter is used to hold the two rods together. Determine the smallest thickness t of the cotter and the smallest diameter d of the rods. All parts are made of steel for which the failure normal stress is fail 500 MPa and the failure shear stress is fail 375 MPa. Use a factor of safety of (F.S.), = 2.50 in tension and (F.S.), = 1.75 in shear. -d- 30 kN 40 mm d - 30 kN t Prob. 7-63 10 mm =
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
Determine the average normal stress developed in rod AB if the load has a mass of 56 kg. The diameter of rod AB is 8mm 8mm A 5 4 3
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb/ft2, determine the state of stress at points Cand D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe. 6 ft 3 ft 上 A B x 12 ft 150 lb/ft²
1341. The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. 4 kN/m 20 mm 60 mm D- 20 mm 0 mm m--15m-- Probs. 13-4041
Determine the maximum force P that can be exerted on each of the two pistons so that the circumferential stress in the cylinder does not exceed 3 MPa. Each piston has a radius of 45 mm and the cylinder has a wall thickness of 2 mm.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

*7-48. The joint is subjected to the axial member force of 27 kN. Determine the average normal stress acting on sections AB and BC. Assume the member is smooth and is 40 mm. thick. 27 kN 60 20