- 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P = 256 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.

- 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P = 256 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 10800 psi, and the vertical deflection of joint D is not to exceed 0.425 in. when a load of P = 3100 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 84 in., b = 32 in., and c = 36 in. Part 1 Answer: T = a i D P B Calculate the torque being applied to the shaft at point B. b C lb-in
8.1 Please help ASAP. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
PLEASE DRAW THE FBD!!! DRAW THE FBD
ı need solution
A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm. The inside diameter is 460 mm and its height is 2.5-m. Solve for the maximum internal pressure that can be implied if the longitudinal stress is only up to 120 MPa, while the tangential stress is only up to 50 MPa.
A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?
A machinery uses a helical tension spring with wire diameter of 3 mm and coil outside diameter of 35 mm. The spring has 9 total coils. The design shear stress is 500 MPa and the modulus of rigidity is 82 GPa. Determine the force that causes the body of the spring to its shear stress in N. Consider ground ends.
Include the FBD of the Problem
SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION
can you help me with this
The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of 221 MPa.
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m