A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength of 250 MPa. The component has an external diameter of 45 mm and a wall thickness of 3 mm. It has a length of 4 m. A1. The component is subject to a torque of 580 Nm. Calculate the Shear Stress at the external surface

Q: State three uses of the combination set

A: Combination set is an measuring tool, it is used to measure angles and lengths.

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

A: For solution refer below images.

Q: How many turns does cog E make?

A:

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 1 3. 9 TypehereIG 2.

A: Correct option: True.

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: What's the answer for Q4 D and E with working out and answer as you already answered A-C

A: a) Write the expression for the specific speed. Here, N represents the rotational speed of the…

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: 0 = 0° A

A:

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True O False

A:

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: used for?

A: Marking circles or distances

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

A: