A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength of 250 MPa. The component has an external diameter of 45 mm and a wall thickness of 3 mm. It has a length of 4 m. A1. The component is subject to a torque of 580 Nm. Calculate the Shear Stress at the external surface A2. The component then has a tensile load applied normal to its cross-section of 38KN. Calculate the resulting longitudinal stress.

Q: Why is 100 at - here?

A: Why is 100 at - here?

Q: Question 1 Compute the lead of a 4 -19 UNC single t

A:

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Identify the number of spur gears available in a Single Purchase Crab Winch a. One b. Three c. Four…

A:

Q: 4. In what standard plates can we index the following. Solve using sil label each values. a. gear of…

A: we have to determine the plate size for manufacturing the given items by simple indexing

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: what is the MMC of shaft dimension 1.375 /- .030?

A: Given: The dimension of shaft  is 1375/-0.30 MMC :MMC stand for  Maximum Material Condition.

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: O a. 45 degree…

A: Drilling is a cutting operation in which a drill bit is used to cut a circular hole in a solid…

Q: Up milling operation is performed for finishing cut. Select one: True O False

A: Down milling is performed for finishing and get smooth surface.

Q: From the following Identify cutting tool made by forging before hardening and grinding. О а. Ob. О…

A: First step for making a tool is

Q: y h с b bh .1

A:

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: 4. In what standard plates can we index the following. Solve using simple indexing anda label each…

A: we have to determine the plates required for simple indexing

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: In this pair number of binary joint is available. O A. four O B. one O C three O D. two

A: A joint is the connection of two or more links at a section. In a fixed or permanent mechanical…

Q: A mass of 25 lb is applied at the end of a 2-inch-diameter rod shown in Figure P2. If the modulus of…

A:

Q: please explain for c) what is Sum of M at hinge

A:

Q: State four espect to consider before selecting correct solvant

A:

Q: From the following Identify cutting tool formed by grinding the end piece of a steel stock is O a. O…

A: Option d is correct.

Q: 1 4 ind the degree of freedom (F) of the mechanism in the figure.

A: Degree of freedom is defined as a number of input required in a mechanism to get the constrained…

Q: голь 40° Find P. do, 25°

A:

Q: A'4- point socket has a drive size of 0.5 inch. Which dimension does this denote? C. Radius of the…

A: A'4- point socket' has a drive size of 0.5 inch means the side of the square is 0.5 inches.

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: Gate AB in Figure is 4 ft wide into the paper, 6 ft long, and has weight W= 800 lb. It is hinged at…

A: The FBD of the diagram is shown below - a) The force of water on gate AB is  - FP = ρgAxFP =…

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :-  Identity the part not belongung to micrometer Ratchet  Clamp  Locknut Frame

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: What is the MMC of the bored holes?

A: Maximum Material Condition(MMC): In GD&T, the MMC is a feature which contains the maximum amount…

Q: 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.