6.2-2 A wood beam is strengthened using two steel plates as shown in Fig. a. The beam has simple sup- ports and an overhang and is subjected to a point load and a uniform load as shown in Fig. b. Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa.

6.2-2 A wood beam is strengthened using two steel plates as shown in Fig. a. The beam has simple sup- ports and an overhang and is subjected to a point load and a uniform load as shown in Fig. b. Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P acting on the simple beam AB (see figure). (a) Data are P = 6.2 kN, L = 3.2 m, d = 1.25 m, b = 80 mm, 1 = 25 mm, h = 120 mm, and h = 90 mm. (b) Find the value of d for which tensile and compressive stresses are the largest. What are these stresses? A, L- PROBLEM 5.5-18
For the truss shown below, use symmetry to determine the displacement of the nodes and the stresses in each element. E=30E6 psi, Elements 1, 2, 4 and 5 have Area=10 in? and element 3 has Area = 20 in?, Use i hand calculations. 6 ft 2 8 ft 8 ft- 20,000 lb
Determine the maximum tensile stress O, and maximum compressive stress o. due to the concentrated load P acting on the simple beam AB (see figure). Data are as follows: P = 8 kN, L =3 m, C = 1.1 m, b = 75 mm, bị =25 mm, h = 100 mm, and hi = 75 mm
A cantilever beam of rectangular cross section is subjected to a concentrated load P = 150 kN acting at the free end (see Figure 1). The beam has width b = 80 mm. and height h = 260 mm. Point A is located at distance c = 0.5 m from the free end and distance d = 220 mm. from the bottom of the beam. a) Using Mohr's circle, calculate the principal stresses ơi and oz and the maximum shear stress Tmax at point A. b) Show these stresses on sketches of properly oriented elements. P h Figure 1: A cantilever beam
A overhang beam hanged at B(6m) has two loads of 8 & 4 kn at 6 and 9 m. Calulate its moment using castigliano's theorem. Also calculate Strain Energy.
Question 1 A thin-walled cylindrical pressure vessel of radius r is subjected simultaneously to internal gas pressure P and a compressive force F acting at the ends (see figure 1) (a) what should be the magnitude of the force F in order to produce pure shear in the wall of the cylinder (b) compute the required thickness of the vessel if force F=190 kN, internal pressure P=12MPa, inner diameter=200mm, and allowable normal and shear stresses are 110MPa and 60MPa, respectively?
5. A beam is 15 x 15 mm in cross-section, and it is 0.95 m long. It is pinned at both ends, and the value for Young's modulus is 135 GPa. What is the critical stress to cause buckling?
In the figure, find the length c of the overhangs so that the beam made of U profile can carry the loading safely. The safety stress (oç) emn = 50 N / mm2, (ob) emn = 80 N / mm2 for the tensile and compression condition of the material. The support range of the beam is L = 6 m, cross-section dimensions a = 210 mm, b = 150 mm and wall thickness t = 40 mm. The °B loading condition is P = 30 kN and q0 = 40 kN / m. (Kesit)
5.10-8 A bridge girder AB on a simple span of length L = 14 m supports a distributed load of max- imum intensity q at mid-span and minimum intensity 412 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q based upon (a) an allowable bending stress oallow = 110 MPa and (b) an allowable shear stress 7 low = 50 MPa. 450 mm 32 mm B L= 14 m - 16 mm- 1800 mm 32 mm 450 mm
Question A cantilever beam (length L) of rectangular cross-section supports an inclined load P at its free end as shown. Calculate the maximum tensile stress due to the load P. Let b-75 mm, h-150 mm, L-1.4 m, P-800 N and 0-30°.
phy
Example (5.3): Find the maximum tensile and compressive stresses for the beam shown in Figure (5.6). 10 KN 2 kN/m 100 mm 50 mm S.E.D (KN) Solution: -10 -14 BM.D(KN.m) -24 Figure (56)