5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P acting on the simple beam AB (see figure). (a) Data are P = 6.2 kN, L = 3.2 m, d = 1.25 m, b = 80 mm, 1 = 25 mm, h = 120 mm, and h = 90 mm. (b) Find the value of d for which tensile and compressive stresses are the largest. What are these stresses? A, L- PROBLEM 5.5-18

5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P acting on the simple beam AB (see figure). (a) Data are P = 6.2 kN, L = 3.2 m, d = 1.25 m, b = 80 mm, 1 = 25 mm, h = 120 mm, and h = 90 mm. (b) Find the value of d for which tensile and compressive stresses are the largest. What are these stresses? A, L- PROBLEM 5.5-18

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Example (5.3): Find the maximum tensile and compressive stresses for the beam shown in Figure (5.6). 10 KN 2 kN/m 100 mm 50 mm S.E.D (KN) Solution: -10 -14 BM.D(KN.m) -24 Figure (56)
A prospector uses a hand-powered winch(see figure) to raise a bucket of ore in his mineshaft. The axle of the winch is a steel rod of diameterd = 0.625 in. Also, the distance from the centerof the axle to the center of the lifting rope isb = 4.0 in.(a) If the weight of the loaded bucket is W =100 lb,what is the maximum shear stress in the axle dueto torsion?(b) If the maximum bucket load is 125 lb and theallowable shear stress in the axle is 9250 psi,what is the minimum permissible axle diameter?
The cross section of a composite beam madeof aluminum and steel is shown in the figure. The moduliof elasticity are EAl = 75 GPa and Es =200 GPa.(a) Under the action of a bending moment that producesa maximum stress of 50 MPa in the aluminum,what is the maximum stress σs in the steel?(b) If the height of the beam remains at 120 mmand allowable stresses in steel and aluminum aredefined as 94 MPa and 40 MPa, respectively,what heights hAl and hs are required for aluminumand steel, respectively, so that both steeland aluminum reach their allowable stress valuesunder the maximum moment?
Solution please
Q3: A hexagonal cross section bar as shown in Figure (2) below, is used as a simply supported beam. The beam carries a central load of 60 kN. Draw the shear stress distribution diagram for a section of the beam at quarter of the beam length from the left hand support. Figure (2) 25 mm 30° 30°
A flat bar of rectangular cross section, length L, and constant thickness tis subjected to tension by forces P (see figure). The width of the barvaries linearly from b1 at the smaller end to b2 at the larger end. Assumethat the angle of taper is small.(a) Derive the following formula Tor the elongation of the ban(b) Calculate the elongation, assuming L=5 ft, t=1.0 in., P= 25 kips, ft, =4.0 in., ft, = 6.0 bland E= 30 x 106 psi.
40 men D Steel t-200 GPa The rigid beam (ABC) supported by three bars, One from the top and two from the bottom. A vertical downward load of W= 60 kN is applied at point B . shown in figure is 200m 50 mm D Brass E-100 GPe 250mm A- Estimate the stress acting on each bar. B- Estimate the downward movement of the beam (АВС).
A cylindrical pressure vessel with flat ends is subjected to a torque 7 and a bending moment M (see figure). ot oc max Zo = M yo The outer radius is 12.2 in. and the wall thickness is 1.0 in. The loads are T = 800 kip-in., M = 1,000 kip-in., and the internal pressure p = 840 psi. Determine the maximum tensile stress, maximum compressive stress and maximum shear stress Tmax in the wall of the cylinder. (Enter the magnitudes in psi. Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) T M psi хо 11474.4981 X Your response differs from the correct answer by more than 10%. Double check your calculations. psi 0 psi
Determine the maximum tensile stress er and maximum compressive stress ec due to the load P acting on the simple beam, 40 (see figure). (a) Data are P = 6.2 kN, L =3.2 m, d =L25 m, b =SO mm, t =25 mm, h = 120 mm, and A, = 90 mm. (b) Find the value of d for which tensile and compressive stresses arc the largest. What are these stresses?