9.3-2 A l-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 1.5 mm. (a) Calculate the magnitude of the distributed load q if the beam has a rectangular cross section (width b = 20 mm, height h = 40 mm). (b) If instead the beam has circular cross section and q = 500 N/m, calculate the radiusr of the cross section. Neglect the weight of the beam. A B. h

9.3-2 A l-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load q. The maximum deflection is measured as 1.5 mm. (a) Calculate the magnitude of the distributed load q if the beam has a rectangular cross section (width b = 20 mm, height h = 40 mm). (b) If instead the beam has circular cross section and q = 500 N/m, calculate the radiusr of the cross section. Neglect the weight of the beam. A B. h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cantilever beam has a length L =12 ft and a rectangular cross section (b= 16 in., h=24 in.), A linearly varying distributed load with peak intensity qoacts on the beam, (a) Find peak intensity q,if the deflection at joint Bis known to be 0.18 in. Assume that modulus E= 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam. TITT В h PROBLEM 9.3-15
I want to answer all the questions by handwriting.
A gymnast with a mass of m = 40 kg is hanging by one hand from the middle of a simply supported beam with a length L = 1.5 m. The beam has a cross-sectional area of A = 4 cm² and a Young's modulus of E = 15 GPa. a. What are the maximum deflection and maximum stress in the beam if it has a circular cross section? b. If it has a square cross section? c. If it has a hollow cross section with a wall thickness t = 0.5 cm? d. Which is the greatest and least and why? L L/2 F Cross Sections - O
. The cantilever beam shown below has a length L, moment of inertia I, and is made from a material with modulus of elasticity E. The load P is applied at the end of the beam. a. Derive the maximum deflection of the beam and show that max Ely" (x) P PL³ ЗЕІ' b. Consider E = 29 x 10³ ksi, P = 6 kip, I = 204 in 4, and L = 15 ft with the length and moment of inertia measured with ±5% and ±10% accuracy, respectively. In 3 significant figures, calculate the deflection and express the variation of its worst-case error. 8max Hint: M(y) =
h F The beam of length 5.9 (m) and cross section base 0.10 (m) and height 0.16 (m) shown is made of plain steel with a modulus of elasticity of 200 (Gpa) and an ultimate strength of 400 (Mpa). The load is 250 (N) and the point q is 4.0 (m) from the wall in the x direction. What is the magnitude of vertical deflection of the beam at point q in units of meters?
7.17 The figure shows a steel beam which is fixedly clamped in A, and which rests on a roller bearing in B. The beam is 5 meters long, and is loaded with a bending moment of 25 kNm at the end. The bearing in B is removed. The cross section is rectangular, with a width of 50 mm. Determine the required height of the cross section when the maximum allowable deflection is 5 mm. Cross section: 25 kNm A h 5 m 50 mm
Find the deflection at the mid-point BC of the loaded beam as shown in the figure by the double integration method. ( E= 200GPA I=6,87x10^-6 m^4)
A fixed-end beam is subjected to a pointload at mid-span. The beam has a rectangular crosssection (assume that the h/b ratio is 2) and is made ofwood (E =11GPa).(a) Find height h of the cross section if the maximumdisplacement of the beam is 2 mm.(b) Calculate the displacement of the beam at theinflection points.
1 B) Calculate the deflection and rotation at point (a) for the beam showing in figure by using unit load method. (E = 200*10° kN/m2, I = 3.125*10³ m*). 30 kN 6 KN/m a 2 2m 3m
The cantilever is subjected to a point force "P" in the middle of the beam span. The beam's modulus of elasticity, E-200 GPa and moment of inertia, l= 6x10^6 mm^4, are the same at every point. Accordingly, in which option is the maximum deflection (vertical displacement) in the beam given in "mm"? P= 12 kN, L= 2.8 m.
The cantilevered beam shown below has a solid 1mm * 1mm cross-section. Find the beam elongation if the material is Lead?
Q.1) For the figure shown, have the following information: (2) Link (1) made Link (2) made of aluminum E =70 GPa A 300 mm2 Calculate the deflection of the beam at point B, when a load P = 55 kN is applied. 4,000 mm of aluminum 2.500 mm E -70 GPa A = 450 mm? 1.400 mMm S00 mm