(a) Find peak intensity q,if the deflection at joint Bis known to be 0.18 in. Assume that modulus E= 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.

Q: An I-profile steel beam is supported and loaded as shown in the figure. If the mass of the block is…

A: E=200 GPa,I=17×106 mm4L=8 m or 8000 mmb=2000mmFor simply supported beam, deflection y is given…

Q: Q4. Under the 5-kip load the support at A rotates 0.002 rad clockwise and settles 0.26 in. (Figure…

A: Draw the free body diagram of the given beam considering the load of 5 kips at P. Apply the…

Q: Q3. For the beam (E = 4.176×106 ksf) shown below, find the deflection at poin 10K с 2' 16k/ft ДА…

A: For the beam E = 4.176 x 106 ksf

Q: Parvinbhai

A: The objective of this question is to determine the deflection at the free end of a cantilever beam…

Q: A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.).…

A: Calculate the moment of inertia of the beam. I=bh312 Here, I is the moment of inertia of the beam, b…

Q: 4) For the beam shown, (a) compute the bending moment. (b) determine the deflection v(x) and check…

A:

Q: Parvinbhai

A: The objective of the question is to determine the equation of the elastic curve of the beam using…

Q: 4. A rectangular shapped beam 150mm broad and 300mm deep by 3m long weighs 20kN. and E for the…

A: Given data: b=150 mmh=300 mmL=3 mW=20 kNE=190 GN/m2   It is required to determine the maximum…

Q: 3P2: A simply supported beam of constant El and length L IS supporting a distributed load omega w…

A:

Q: Use (1) Find deflection superposition method to find (El is constant) at C

A:

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: 7) Use strain energy to calculate the strain energy of the beam in the figure in terms of the…

A:

Q: h L P A cantilever beam has a length L = 8 m and supports a load of P = 9 kN at its free end. The…

A:

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: Beam ABC is loaded by a uniform load q andpoint load P at joint C. Using the method of…

A: Given data as per question  L = 4 m, a = 2 m , q = 15 kN/m, P = 7.5 kN,E = 200 GPa,  I = 70.8 X106…

Q: Consider the beam with properties and loadings as described in the figure and parameter table.…

A:

Q: Problem 2: For the beam shown, determine the maximum deflection. E=2000ksi, 1=40000 in 60k A 10' B…

A: Given data  E = 2000 ksi  I = 40000 in^4 P= 60kips Find the maximum deflection

Q: The simply supported beam loaded as shown. The length of the beam is 6 m, a = 4 m, the load P = 4000…

A: Given                     Load, P = 4000 N                  Length, L = 6 m Moment of inertia, I =…

Q: Quiz: A straight beam ABCD is rigidly built-in at A and D and carries point loads of § kN at B and…

A: Fixed end moments are the reaction moments formed in a beam member under specific load conditions…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.