7) Use strain energy to calculate the strain energy of the beam in the figure in terms of the applied force P, applied moment M。, the length L, modulus E, and area moment of inertia I. Then use Castigliano's theorem to calculate the deflection of the tip. M P x

Q: Which of the following statement is correct Select one: Friction causes objects to slip down…

A: Friction force is directly proportional to the normal force acting to body and independent of area…

Q: If the analysis of the forces involved on an object produces a negative answer for a force: The…

A: If doing calculation and getting any force hwith negative that means, The negative sign indicates…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: Calculate the time to complete one circular motion. How to double the time?

A: Given data:Helicopter mass = 400 kgcircular motion radius, r = 20 mRotor blade resonant frequency =…

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: lease write a precise overview/description of the precision tweezer below specifically for each…

A: Given Data : Precision tweezer

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: Given Drafting To find Type of drawing Angle of projection Scale of drawing Original length of shaft…

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: Files are used for removing large of amount of materials. Select one: True False

A:

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: In drawing process, tensile forces are used to reduce the cross section of the workpiece. Select…

A: The drawing process is generally is done at the room temperature. To reduce the required forces, it…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Explain the diagrame! C. Ca

A: Solution:   In the diagram, Cm is the Moment Coefficient. CL is the Lift Coefficient.

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Calculate the time to complete one circular motion.

A:

Q: A solid cylinder is rolling down a ramp that is rough enough to cause the cylinder to roll without…

A: This question is solved with the help of the law of conservation of energy. Under pure rolling,  The…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: Rolling friction occurs when one surface slides over another surface  Select one: True False

A: Rolling friction is seen between the two surfaces which are in rolling.contact

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: Force 20 N on object does not displace the object. What is work done value

A: To Find :  the work done . Given :  The Force is F=20 N. The displacement is d=0. Formula used: The…

Q: Required information Sally is making a sine bar, which is used to machine angles on parts (see the…

A: Given data: Thickness (t)=1.25 inGroove angle=90°Cylinders diameter d=1 inD=5.6 inθ=22.5° Need to…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: This statement is true or false? Process of making raw material to a final desired product is called…

A: Given Data : Raw Material Final desired product

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Center of gravity of a plane area. Shear force. Point of contraflexure.

A: Centre of gravity of a plane area: The centre of gravity of a plane area is a point inside or…

Q: The spool shown in the figure has a weight of WAB and its center of gravity is located at its center…

A:

Q: Subject Engineering; textbook "AutoCAD and its Applications"  1- What is a drawing template? 2-…

A: 1. Drawing Template :-  The drawing Template file in AutoCAD is a drawing file that has been saved…

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: A six inch diameter cylinder with a two inch rod pushes out its full stroke of 20 inches in 1.5…

A: Forward stroke Area : π462-22=25.13 in2 Volume : V=A×L=502.65 in3 Flow rate : Q=Vt=335.1 in3/s…

Q: Engineering Drawing: Dimensions

A:

Q: In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A: In wire drawing, Material is extruded .

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.