5.8-7A steel beam of length L = 16 in. and cross- sectional dimensions b = 0.6 in. and h = 2 in. (see figure) supports a uniform load of intensity q = 240 lb/in., which includes the weight of the beam. Calculate the shear stresses in the beam (at the cross section of maximum shear force) at points

5.8-7A steel beam of length L = 16 in. and cross- sectional dimensions b = 0.6 in. and h = 2 in. (see figure) supports a uniform load of intensity q = 240 lb/in., which includes the weight of the beam. Calculate the shear stresses in the beam (at the cross section of maximum shear force) at points

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.8.7P: A steel beam of length L = 16 in. and cross-sectional dimensions h = 0.6 in. and h = 2 in. (see...

See similar textbooks

Related questions

Q: Q3: Draw the shear force and bending moment diagrams for the loaded beam shown (see figure below). (…

A: Draw the free-body diagram of the beam.

Q: Calculate the maximum shear stress Tmax and the maximum bending stress σmax in a simply supported…

A: Given data: The uniform load on the beam, w = 18 kN/m. The length of the beam, l = 1.75 m. The…

Q: A beam subjected to a bending test has internal vertical shear force V=2000N. The cross-sectional…

Q: 5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P…

Q: 3. A beam with a rectangular cross section of dimensions ax 1.5a is made from a b in the figure…

Q: A Simply Supported beam of 4 m span is in the form of hollow square bar (120x120 mm) as shown in…

Q: The composite beam in the figure is made of timber with an elasticity modulus of 10 GPa and steel…

A: Composite beam of timber ans steel.

Q: 5 kN/m 3 cm Q.3 Find the maximum compression and tension beam stress for the cross section as figure…

A: The center of gravity of the given figure is calculated as: y=A1y1+A2y2A1+A2 here, A1 represents…

Q: A wood beam with a rectangular cross section(see figure) is simply supported on a span oflength L.…

A: Given data as per question b = 80 mm, h =140 mm, L =1.75 m, α = 22.580 q = 7.5 kN/m. Calculations…

Q: A cantilever beam AB, loaded by a uniform load and a concentrated load (see figure), is constructed…

A: If the cross section has the dimensions stated and the moment of inertia about the z-axis is 3.10…

Q: A D B L a D X 야 나 b dik

Q: 5.10-1 through 5.10-6 A wide-flange beam (see fig- ure) is subjected to a shear force V. Using the…

A: As the question is having more than three sub parts, first three are solved.

Q: A simply supported composite beam 3 m long carries a uniformly distributed load of intensity q 3.0…

Question

100%

5.8-7 A steel beam of length L = 16 in. and cross-
sectional dimensions b = 0.6 in. and h = 2 in. (see
figure) supports a uniform load of intensity
q = 240 lb/in., which includes the weight of the beam.
Calculate the shear stresses in the beam (at the
cross section of maximum shear force) at points

located 1/4 in., 1/2 in., 3/4 in., and 1 in. from the top
surface of the beam. From these calculations, plot a
graph showing the distribution of shear stresses from
top to bottom of the beam.
q = 240 lb/in.
h = 2 in.
b = 0.6 in.
L = 16 in.
PROBLEM 5.8-7

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A singly symmetric beam with a T-section (see figure) has cross-sectional dimensions b = 140 mm, a = 190, 8 mm, b. = 6,99 mm, and fc = 11,2 mm. Calculate the plastic modulus Z and the shape factor.
A cantilever beam A3, loaded by a uniform load and a concentrated load (sec figure), is constructed of a channel section. (a) Find the maximum tensile stresser, and maxi-mum compressive stress trcif the cross section has the dimensions indicated and the moment of inertia about the - axis (the neutral axis) is t = 3.36 in4. Note: The uniform load represents the weight of the beam. Find the maximum value of the concentrated load if the maximum tensile stress cannot exceed 4 ksi and the maximum compressive stress is limited to 14.5 ksi. How far from A can load P = 250 lb be positioned if the maximum tensile stress cannot exceed 4 ksi and the maximum compressive stress is limited to 14.5 ksi?
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress raver (obtained by dividing the shear force by the area of the web) and the ratio i^/t^ The shear force carried in the web and the ratio K b/K. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-2 Dimensions of cross section: b = 180 mm, v = 12 mm, h = 420 mm, i = 380 mm, and V = 125 kN.
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress t (obtained by dividing the shear force by the area of the web) and the ratio tmax/taver. The shear force Vweb/V carried in the web and the Vweb/V. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-1 Dimensions of cross section: b = 6 in,, ï = 0.5 in., h = 12 in,, A, = 10.5 in., and V = 30 k.
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress raver (obtained by dividing the shear force by the area of the web) and the ratio i^/t^ The shear force carried in the web and the ratio V^tV. Noie: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-3 Wide-flange shape, W 8 x 28 (see Table F-L Appendix F); V = 10 k
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress raver (obtained by dividing the shear force by the area of the web) and the ratio i^/t^ The shear force carried in the web and the ratio V^tV. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-4 Dimensions of cross section: b = 220 mm, f = 12 mm, h = 600 mm, hx= 570 mm, and V = 200 kN.
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress raver (obtained by dividing the shear force by the area of the web) and the ratio i^/t^. The shear force i^/t^ carried in the web and the ratio V^tV. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-6 Dimensions of cross section: b = 120 mm, a = 7 mm, h = 350 mm, hx= 330 mm, and K=60kN.
A cantilever beam of length L = 2 m supports a load P = 8,0 kN (sec figure). The beam is made of wood with cross-sectional dimensions 120 mm x 200 mm. Calculate the shear stresses due to the load/"at points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam.
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress raver (obtained by dividing the shear force by the area of the web) and the ratio i^/t^ The shear force carried in the web and the ratio V^tV. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-5 Wide-flange shape, W 18 x 71 (sec Table F-l, Appendix F); V = 21 k.
A beam with a guided support and 10-ft span supports a distributed load of intensity q = 660 lb/ft over its first half (see figure part a) and a moment Mq = 300 ft-lb at joint B. The beam consists of a wood member (nominal dimensions 6 in. x 12 in. and actual dimensions 5.5 in. x 11.5 in. in cross section, as shown in the figure part b) that is reinforced by 0.25-in.-thick steel plates on top and bottom. The moduli of elasticity for the steel and wood are £s = 30 X 106 psi and £"w = 1.5 X 106 psi, respectively. Calculate the maximum bending stresses trs in the steel plates and rw in the wood member due to the applied loads. If the allowable bending stress in the steel plates is = 14,000 psi and that in the wood is (T.dV!= 900 psi, find qmiiX. (Assume that the moment at .fi, A/0, remains at 300 ft-lb.) If q = 660 lb/ft and allowable stress values in part (b) apply, what is Müm^ at B?
A simple beam AB is loaded as shown in the figure. Calculate the required section modulus S if ^aibw = IS,000 psi, L = 32 ft, P = 2900 lb, and g = 450 lb/ft. Then select a suitable I-beam (S shape) from Table F-2(a), Appendix F, and recalculate 5 taking into account the weight of the beam. Select a new beam size if necessary. What is the maximum load P that can be applied to your final beam selection in part (a)?
A wood beam with a rectangular cross section (see figure) is simply supported on a span of length L. The longitudinal axis of the beam is horizontal, and the cross section is tilted at an angle a. The load on the beam is a vertical uniform load of intensity q acting through the centroid C. Determine the orientation of the neutral axis and calculate the maximum tensile stress bmaxif PROBLEMS 6.4-2 and 6.4-3 b = 80 mm, b = 140 mm, L = 1,75 m, a — 22.5°, and q = 7.5 kN/m.