5.14A 100-foot-long surveyor's steel tape with a cross-sectional area of 0.006 square inch must be stretched witha pull of 16# when in use. If the modulus of elasticity ofthis steel is E = 30,000 ksi, (a) what is the total elongation8 in the 100 foot tape and (b) what unit tensile stress is pro-duced by the pull?a. Elongationb. Tensile Stress

Length of the steel tape, L=100feet=100×12=1200inchesCross-sectional area, A=0.006 in2Applied…

Answered: 5.14 A 100-foot-long surveyor's steel…

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter65: Achievement Review—section Six

Section: Chapter Questions

Problem 44AR: Solve these prism and cylinder exercises. Where necessary, round the answers to 2 decimal places...

See similar textbooks

Similar questions

Solve these prism and cylinder exercises. Where necessary, round the answers to 2 decimal places unless otherwise specified. A solid right cylinder 9.55 centimeters high contains 1910 cubic centimeters of material. Compute the cross-sectional area of the cylinder.
Compute the number of cubic centimeters of material in the locating saddle shown. Round the answer to the nearest cubic centimeter.
The kinetic energy E of an object varies jointly with the object’s mass m and the square of the object’s velocity v . An object with a mass of 50 kilograms traveling at 16 meters per second has a kinetic energy of 6400 joules. What is the kinetic energy of an object with a mass of 70 kilograms traveling at 20 meters per second?
Suppose a spring with spring constant 8 N/m is horizontal and has one end attached to a wall and the other end attached to a mass. You want to use the spring to weigh items. You put the spring into motion and find the frequency to be 1.4 Hz (cycles per second). What is the mass? Assume there is no friction. Mass= help (units)
A steel rod 3/4 in. in diameter and 25 ft long is subjected to an axial tensile load of 15,000 lb. Compute a. stress b. strain c. total elongation
Is demand elastic, inelastic, or unit elastic at a price of p = 100? х 3D 875 — р — 0.05p?
An engineer wants to compare the tensile strengths of steel bars that are produced using a conventional method and an experimental method. (The tensile strength of a metal is a measure of its ability to resist tearing when pulled lengthwise.) To do so, the engineer randomly selecto
An aluminum cylinder with a radius of 1.1 cm and a height of 82 cm is used as one leg of a workbench. The workbench pushes down on the cylinder with a force of 3.2×10^4N. What is the compressive strain of the cylinder? Young's modulus for aluminum is 7.0×10^10Pa Express your answer using two significant figures. b)By what distance does the cylinder's height decrease as a result of the forces on it?
A shell of mass 4 kg is shot upward with an initial velocity of 200 m/sec. The magnitude of the force on the shell due to air resistance is 20 the ground? What is the maximum height? Assume the acceleration due to gravity to be 9.81 m/s². When will the shell reach its maximum height above the ground? The shell will reach maximum height after 18.16 seconds. (Round to two decimal places as needed.) What is the maximum height? The maximum height is 1747 m. (Round to the nearest whole number as needed.) 3 (...) When will the shell reach its maximum height above
A pipe has an inside diameter of 1.6 cm. It carries water into the first floor of a house at a speed of 0.93 m/s and a pressure of 173 kPa. The diameter of the pipe is then increased to 2.4 cm and the pipe lowers to the basement 6.7 m below the input point. a. What is the speed at the basement level? m/s b. What is the water pressure at the basement level? kPa
1 (2) 1,800.00 mm (1) (2) 1,400.00 mm A B C Rigid bar P Rigid bar ABC is supported by three symmetrically- positioned vertical rods as shown. There is no strain in the vertical rods before load P is applied at B. After load P is applied, the normal strain in rod (1) is 950.00 µɛ. Determine the normal strain in rods (2) in units of με.
The conical tank shown here filled with olive oil weighing 49 Ib/ft. How much work does it take to pump all y-2x or xy of the oil to the rim of the tank? (7.14)

SEE MORE QUESTIONS

Recommended textbooks for you

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

College Algebra

Algebra

ISBN:

9781337282291

Author:

Ron Larson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS