5. Which one of the following is the correct definition of ultimate tensile strength, as derived from the results of a tensile test on a metal specimen: (a) the stress encountered when the stress-strain curve transforms from elastic to plastic behaviour, (b) the maximum load divided by the final area of the specimen, (c) the maximum load divided by the original area of the specimen, or (d) the stress observed when the specimen finally fails?

5. Which one of the following is the correct definition of ultimate tensile strength, as derived from the results of a tensile test on a metal specimen: (a) the stress encountered when the stress-strain curve transforms from elastic to plastic behaviour, (b) the maximum load divided by the final area of the specimen, (c) the maximum load divided by the original area of the specimen, or (d) the stress observed when the specimen finally fails?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the Tensile experiment, the function of a load cell is to: Select one: a. Measure the applied force. b. Measure the applied strain. c. Measure the applied stress. d. Measure the specimen elongation.
Mark the following points on an Engineering Stress-Strain curve. Plastic limitElastic limitFracture strengthYield strengthUltimate tensile strength
Whats the correct answer for this please ?
An impact test was done on specimen M and R and the results are shown in Fig. Q2(c) and Table Q2(c). Based on the obtained results, choose whether specimen M or R is brittle or ductile in terms of: Impact strength Fracture surface Specimen M Specimen Impact Strength (J/m²) Fig. Q2(c) Table Q2(c) M 4.35 x 105 Specimen R R 1.21 x 106
Extension Compression Determine the engineering strain "e" and the true strain "e" for each of the following situations of extending a bar of length L or compressing a billet of height h: Extension from L to 1.002 L Compression from h to 0.998 h Extension from L to 1.9L Compression from h to 0.1h Compression from h to zero height
A specimen is originally 1.5 ft long, has a diameter of 0.7 in., and is subjected to a force 550 lb. When the force is increased to 1900 lb, the specimen elongates 0.9 in. Determine the strain on the specimen and the modulus of the material. a. Strain Answer: _______ in./in. b. Modulus of Elasticity Answer: _______ ksi
Hooke's law is used to correlate true stress and true strain in the plastic region of the stress/strain curve. true or false
4. For a brass alloy, the stress at which plastic deformation begins is 345 MPa and the modulus of elasticity is 103 GPa. What is the maximum load that may be applied to a specimen with a cross-sectional area of 130 mm² without plastic deformation? b. If the original specimen length is 76 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
At operating stress of 420MPa, the number of cycles to fail a specimen is 65 cycles. At operating stress of 360MPa, the number of cycles to fail the specimen is 390 cycles, and at operating stress of 130MPa, the number of cycles to fail the specimen is 11,900 cycles. A test sequence as follows is designed: first, operating stress of 420MPa for 7 cycles, second, operating stress of 360MPa for 65 cycles, and third, operating stress of 130MPa for 325 cycles. Determine at what number of cycle and which operating stress level the specimen would be expected to fail if the above sequence is repeated.
Part of the stress-strain diagram where the material stress lies between the proportional limit and the upper yield point
A mild steel tensile specimen of initial length 44 mm and initial diameter 6.4 mm is subjected to a tensile test and the following data are obtained. - Yield Strength as 88 MPa - Maximum Strength as 212 MPa - Fracture Strength as 152 MPa - Percentage of Elongation as 63 % - Percentage of Reduction in area as 39% Determine the Final length, Final area, Yield load, Ultimate load
QUESTION 7 Which governing equations are required to solve a plane elasticity problem? Boundary conditions Equilibrium condition and boundary conditions Equilibrium conditions, boundary conditions, and the compatibility equation QUESTION 8 Which of the following conditions must a structure meet to produce a state of plane strain parallel to the x-y plane? Thin-walled Uniform in z-direction Dimension in z-direction that is much smaller than x and y QUESTION 9 What is the major advantage of using the Airy stress function for plane isotropic solids? Reduces the governing equations to only the boundary conditions and compatibility equation Reduces governing equations to a single function with a single unknown QUESTION 10 Airy stress functions are applicable for solving all elasticity problems. True False