A specimen is originally 300 mm long, has a diameter of 14 mm, and is subjected to a force of 2kN. When the force is increased from 2kN to 8kN, the specimen elongates 0.225 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express the answer to three significant figures and include the appropriate units.

Q: The elastic region of the tension stress-strain diagram for an aluminum alloy is shown in (Figure…

A: The new diameter of the specimen.Given:The diameter of the specimen is .The shear modulus is .The…

Q: What is the modulus of elasticity

A: force F = 613 kNdiameter d = 43 mm = 0.043 mlength L = 304 mm = 0.304 melongate length l = 0.00224 m

Q: A cylindrical bar of metal having a diameter of 18.3 mm and a length of 209 mm is deformed…

A: Diameter of specimen, d=18.3 mm Length of specimen, L=209 mm Tension force, F=52500 N Modulus…

Q: At the proportional limit, a 20-mm-thick x 75-mm-wide bar elongates 7.1 mm under an axial load of…

A: Given Data- Area A=20mm*75mm Change in length =7.1mm Load P=465KN L=1.6m We have to find Modulus of…

Q: A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load,…

A:

Q: What is the change in dimension in the 2 direction in mm?  What is the σ1 component of the stresses…

A: Given data: A 50 mm cube of graphite reinforced material was extended by 0.90 mm in the 1-direction.…

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

A:

Q: Nominal or engineering strain in the rod

A: Given DataThe gauge length of the specimen The initial diameter d0 =0.5 inYield stress f…

Q: Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both…

A:

Q: The block is subjected to a force V = 48 kN . What is the resulting deflection Δ?

A: Given information:d1 = 3 cmd2 = 3.7 cmd3 = 4 cmV=48 kN

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’s ratio of 0.35 is…

A:

Q: A bar having a length of 125 mm and cross-sectional area of 467.5 mm² is subjected to an axial force…

A:

Q: A titanium alloy (Ti-5Al-2.5Sn) specimen with the dimensions shown below is subjected to a uniaxial…

A: The stress of a bar is given by,  , where P is the normal load and A is the cross-section area of…

Q: Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.49 cm & the…

A: Given data: The external diameter of the cylinder is D = 23.1 mm. The internal diameter of the…

Q: 2. A bar having a length of 5 in. and cross-sectional area of 0.8 in? is subjected to an axial force…

A: Given:L=5 inA=0.8 in2F=8000 lb∆L=0.003 in

Q: A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of…

A:

Q: A 1.6 ft long rod is made from the material, having the elastic modulus of E = 176 ksi and the yield…

A:

Q: n of aluminum having a rectangular cross section 9.6 mm × 13.0 mm (0.3780 in. × 0.5118 in.) is…

A: Given:Area, A=9.6*13.0 mm2F=35800 NE=69 GPa

Q: Consider a material with the stress-strain diagram shown where the yield point is 400 MPa (similar…

A: Given : Yield stress (initial)Material stressed upto (final)To find : Change in modulus of…

Q: Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.1 cm & the…

A:

Q: A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter…

A:

Q: The principal plane stresses and associated strains in a plane at a point are 0₁ = 35 ksi, 0₂ = 15…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.