At operating stress of 420MPa, the number of cycles to fail a specimen is 65 cycles. At operating stress of 360MPa, the number of cycles to fail the specimen is 390 cycles, and at operating stress of 130MPa, the number of cycles to fail the specimen is 11,900 cycles. A test sequence as follows is designed: first, operating stress of 420MPa for 7 cycles, second, operating stress of 360MPa for 65 cycles, and third, operating stress of 130MPa for 325 cycles. Determine at what number of cycle and which operating stress level the specimen would be expected to fail if the above sequence is repeated.

At operating stress of 420MPa, the number of cycles to fail a specimen is 65 cycles. At operating stress of 360MPa, the number of cycles to fail the specimen is 390 cycles, and at operating stress of 130MPa, the number of cycles to fail the specimen is 11,900 cycles. A test sequence as follows is designed: first, operating stress of 420MPa for 7 cycles, second, operating stress of 360MPa for 65 cycles, and third, operating stress of 130MPa for 325 cycles. Determine at what number of cycle and which operating stress level the specimen would be expected to fail if the above sequence is repeated.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: How is the nominal or engineering strain found directly from the strain gage?

A: Engineering strain is defined as ratio of total amount of stretch that a part undergoes or the…

Q: Fatigue angle in Failure (record number of cycles before failure) Large Metal Paperclip Small Metal…

A: 1.Small metal subjected to a large number of the cycle before failure this is because metal has…

Q: A three-point bending test was performed on an aluminum oxide specimen having a circular cross…

A: Given data:- Material aluminum oxide For circular cross-section Radius (r)=5.6 mm fracture load…

Q: A gauge # 10 HSLA steel for an automotive application has a Young’s modulus of 200 GPa, a yield…

A: Find the punch force required

Q: The following results were obtained in a tensile test on a mild steel specimen of original diameter…

A: According to Hooke's law, Young's Modulus of Elasticity is defined as the ratio of longitudinal…

Q: A specimen has a yield strength of 1390 psi at room temperature (70 degrees F) and 910 psi when it…

A: Introduction: The yield strength of a material is the strength beyond which the material begins to…

Q: The following stresses were measured for a specimen: 011 = 94 MPa; 022 = 155 MPa; ơ12 = 85 MPa…

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

Q: What are the elastic modulus (E) and the Poisson's ratio () used to indicate? 2. Illustrate the…

A: The elastic modulus (E) and Poisson's ratio are two important parameters used to describe the…

Q: n ductile materials occurs when the stresses at the crack tip ation factors for ductile materials…

A: a) factor of safety is always used while designing a components ( True) b) small radius of…

Q: In a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The…

A: Given data:- Length of the sample (l) = 2 in diameter of the sample (d)=0.5 in Applied tensile load…

Q: The % of error between a theoretical shear modulus of GPa and an experimental modulus of rigidity of…

A: Option d is correct.

Q: Please match different stresses to the stress value corresponding to the different points on the…

Q: Nominal or engineering strain in the rod

A: Given DataThe gauge length of the specimen The initial diameter d0 =0.5 inYield stress f…

Q: In what situations would you use a hardess test instead of a Tensile test?

A: The objective of the question is to understand the scenarios where a hardness test would be more…

Q: Suppose you need to design a tension test machine capable of testing specimens that have nominal…

Q: You have built the majority of the tension testing machine, but much of the instrumentation is still…

A: The diameter is

Q: Given the following stress-strain graph: a. is the modulus of elasticity of "A-514" greater, less or…

A: (a): the modulus of elasticity of A-514 is same asA-572 because the slope of initial stress strain…

Q: 39) A tensile test specimen has a gauge length=2in. and a diameter of 0.875in. Yielding occurs at a…

Q: 40)A tensile test specimen has a gage length=3.0 inches and a diameter= .75 inches. Yielding occurs…

A: Given:

Q: Part D-Permanent elongation of the specimen if the specimen is loaded until its nominal stress value…

A: Givenσ=65ksiε=0.06

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

At operating stress of 420MPa, the number of cycles to fail a specimen is 65
cycles. At operating stress of 360MPa, the number of cycles to fail the
specimen is 390 cycles, and at operating stress of 130MPa, the number of
cycles to fail the specimen is 11,900 cycles. A test sequence as follows is
designed: first, operating stress of 420MPa for 7 cycles, second, operating
stress of 360MPa for 65 cycles, and third, operating stress of 130MPa for 325
cycles. Determine at what number of cycle and which operating stress level
the specimen would be expected to fail if the above sequence is repeated.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data and what is to find.

VIEW

Step 2: The number of cycles at which the specimen will fail is calculated:

VIEW

Step 3: Calculate the operating stress level:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following curve is a result of a tensile test. The gauge length was 2 in, and the specimen diameter was 0.505 in The fracture area was round with a diameter of 0.391 in. Remember to com 20000 Force (pounds force) 15000 10000 5000 0 16. The yield strength is 0 0.2% O 80,000 pl O 12.000 p 060,000 pl 85,000 p 0.1 0.2 Extension (inch) 0.3 0.4
The results of a tensile test are: Diameter of the specimen Gauge length Load at limit of Proportionality Extension at the limit of Proportionality Maximum Load : 10mm :40 mm : 70kN :0.08mm. :100 kN Calculate stress at limit of proportionality and young's modulus.
Hello, the stress and cycles required for this question is Stress 1 = 420MPa at 7 cycles, Stress 2 = 360MPa at 65 cycles and Stress 3 = 130MPa at 325 cycles. Use the first three cycles (which shows how many cycles at that stress level to failure) to calculate when the specimen will fail if it underwent test of 7 cycles at 420MPa, then undergoes 360MPa for 65 cycles and finally 130MPa at 325 cycles. Will the specimen fail? Please show calculations of failure
QUESTION The following data were obtained during a tension test of a low carbon steel specimen having a gauge length of 100 mm. At the point where the stress strain curve deviated from linearity, the load was 35KN, the gauge length was 102.5 mm and the diameter of the specimen was 1.6 mm. Before necking began, loads of 45 KN and 55 KN produced gauge lengths of 103.4 mm and 107.7 mm respectively. Calculate (a) The Modulus of elasticity (b) The Strainhardening exponent
(d) Following experimental data (TableQ1b) has obtained from the torsion test for the specimen dimension given in Table Q1a. Determine the material of a circular bar. (Take the material Poisson's Ratio as 0.32) Table Q1a Specimen Dimensions Dimensions Material Diameter (mm) 6 Length (mm) 77.15 TableQ1b Experimental Results from Torsion test Angular Deflection Degree Radian Torque/Nm 0.5 0.008727 0.06 1 0.017453 0.47 1.5 0.02618 0.76 2 0.034907 1.01 2.5 0.043633 1.32 3 0.05236 1.65 3.5 0.061087 1.99 4 0.069813 2.32 4.5 0.07854 2.66 5 0.087267 3.00 5.5 0.095993 3.33 6 0.10472 3.64 10 0.174533 5.92 20 0.349066 7.74 30 0.523599 8.07 40 0.698132 8.17 50 0.872665 7.93 60 1.047198 8.10 70 1.221731 8.2 80 1.396264 8.4 90 1.570797 8.24 100 1.74533 8.7 110 1.919863 8.7 120 2.094396 8.7 180 3.141594 9.02 240 4.188792 9.11 300 5.23599 9.48 360 6.283188 9.51 420 7.330386 9.71
1. A tensile test was conducted on a metal "505" specimen and the following stress-strain curves were generated, both curves generated from the same set of data. Use the graphs to fill in the mechanical properties of the material tested in the box below. Don't forget units! Stress vs Strain Stress, psi Stress, psi 80000 70000 60000 50000 40000 30000 20000 10000 0 0.00 80000 70000 60000 50000 40000 30000 20000 10000 0.02 0 0.000 0.002 0.04 0.004 0.06 0.006 0.08 0.10 Strain Stress vs Strain 0.008 0.12 Elastic Modulus, E: 0.2% Offset Yield Strength, oo: Tensile Strength, ou: Breaking Strength, of: % Elongation: 0.14 0.010 0.012 0.014 Strain 0.16 0.18 0.016 0.018 0.20 0.020
please wright by hand
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Q19 and Q20
A tensile test was performed on a metal specimen with a diameter of 1/2 inch and a gage length (the length over which the elongation is meas- ured) of 4 inches. The data were plotted on a load-displacement graph, P vs. AL. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/AL = 1392 kips/in. What is the modulus of elasticity? BI
Note: this is not assignment question and not a graded question
I need the answer as soon as possible