5. There are three sources that would affect the current flow in this circuit. Find the currentthrough the 4k2 resistor that is caused solely by the 24V source (i.e., remove the 2mA and12V sources using the correct methods).(20 points)24 V +9k,wwwww4kS2mA24ΚΩwww++12Vwww6k24ΚΩ

The question asks for the current response in one of the resistors due to solely one energy source…

Answered: 5. There are three sources that would…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
All the lamps from Lamp #1 to Lamp #7 are designed to work with a nominal Voltage Vlamp of 120V and their resistance Rlamp is constant and do not depends on the temperature. Using this information solve the questions below. The Channel 2 has four lamp connected as shown in the Figure 2 and again you want to be sure that will not be a black-out in the middle of the performance. Please determine if the Channel 1 can work using the variable ALPHA from 0% to 100%. Yes/No, justify your answer with your calculations. No justifications – No points
Show me how to approach this problem with steps please
I need help understanding this question, what does this question is talking about
Q4
R A IOLL 4) 2A A 2a R4 20V a) Find the voltage at point A due to the 20V source only. b) Find the voltage at point A due to the 2A current source only. c) Find the voltage at point A when both are activated.
What Rx in parallel with 40 ohm will provide and Req of 24 ohm?
How would I approach this question? Do I need to use Kirchoff's junction rules or can I just subtract the voltage drop?
An unbonded strain gauge shown in figure 1 is used to measure pressure. As the pressure is applied to the diaphragm, the upper strain wires R1 and R3 are stretched and the resistance in each wire increase by AR while R2 and R4 are compressed with their resistance decreased by the same amount AR. The four strain gauges are connected into a bridge circuit with an excitation voltage of Vpc of 5 volts as shown in figure 2 below. Strain Gauge R1 R3 R2 R4 R1 R2 Vdc Va Signal Conditioning Voltage Output Circuit Vb Force Rod R4 R3 Figure 1 Figure 2 Diaphragm 1. Show that the output of the bridge, Vpa = (AR/R ) Vdc where R is the initial resistance of each wire. (Hint : Let R1=R3 = R + AR, R2=R4= R- AR and use voltage divider rule to solve for Vpa = Vb -Va) 2. If the maximum stress gauge wire is limited to 300MPA and the Elastic modulus of the material is 210GPA, calculate the range of voltage output from the bridge. Assume the strain gauges have a gauge factor of 2.0. 3. If the initial…
The figure shows a circuit. The switch S can be closed on either point A or C, but not both at the same time. Use the following quantities: V₁ = V₂ = 12 V R₁ = R4 = 1.00 R₂ = R3 = 2.00 [ R 4 O 2A O 6 A O 1 A O 12 A S О ЗА R₁ Determine the current through R₁ when the switch S is closed on A. W K Bm! B
Two resistors in series draws 5A from a 30-V dc source. If the value of the second resistor is doubled, the current drops to 3A. Determine the total current when connected in parallel to a 24-V dc source.
Explain this diagram for a dummy

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

5. There are three sources that would affect the current flow in this circuit. Find the current through the 4k2 resistor that is caused solely by the 24V source (i.e., remove the 2mA and 12V sources using the correct methods). (20 points) 24 V + 9k, ww www 4kS 2mA 24ΚΩ www ++ 12V www 6k 24ΚΩ