5. A solid steel disk E=200X1019 N/m^2 start rotation from the rest with constant acceleration. When the disk changed an angular position by 180 degrees, a small disk attachment (hummer) hit an aluminum rod E = 70 x 10^9 N/m^2. At that moment the angular velocity was 2500 rad/s. Diameter of the aluminum rod is 0.1 m. Please, find strain in the rod. R= 2m Rad

5. A solid steel disk E=200X1019 N/m^2 start rotation from the rest with constant acceleration. When the disk changed an angular position by 180 degrees, a small disk attachment (hummer) hit an aluminum rod E = 70 x 10^9 N/m^2. At that moment the angular velocity was 2500 rad/s. Diameter of the aluminum rod is 0.1 m. Please, find strain in the rod. R= 2m Rad

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monelmetal is subjected to five torques acting in the directionsshown in the figure. The magnitudes of thetorques are T1 = 1000 lb-in., T2 =T4 = 500 lb-in., andT3 =T5 = 800 lb-in. The tube has an outside diameterof d2 =1.0 in. The allowable shear stress is 12,000 psiand the allowable rate of twist is 2.0°/ft.Determine the maximum permissible insidediameter d1 of the tube.
12 +bh,d+bh 12 + b₂h₂d² Question 1.8 A box beam shown in Figure Q1.8 is subject to a bending moment about the z axis. The normal stress with the maximum magnitude due to the bending moment occurs at A IC B 4 Figure Q1.8 O a. Point C O b. Point A Oc. Point B O d. Point D
Problem The maximum stress produced by a pull in a bar of length 1 m is 150 N/mm2. The area of cross-sections and length are shown in Fig. 4.3. Calculate the strain energy stored in the bar if E = 2 x 105 N/mm2. 200 mm 100 mm 200 mm A C D 475 mm 50 mm 475 mm
A hollow circular bar of cylindrical steel is 1.5 m long and has inner and outer diameters of 40 and 60 mm. (a) What is the largest torque I can apply to the circular bar if the shear stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shear stress in the circular bar? (answers: (a) 4084.1 N.m (b) 2722.7 N.m)
The 50-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and concentrated torsional loadings shown where T = 1.75 kN·m. (Figure 1) Part A Figure B 0.4 m T 2 kN·m/m 0.6 m 1 of 1 Determine the angle of twist at the free end A of the shaft. Express your answer in degrees to three significant figures. ΜΕ ΑΣΦ vec |= 1.89 Submit Previous Answers Request Answer × Incorrect; Try Again; 23 attempts remaining < Return to Assignment Provide Feedback ?
The stresses shown in the figures act at a point in a stressed body. Determine the normal and shear stresses at this point on the inclined plane using (i) the stress transformation equations. Compare the solution from both the methods.
A solid circular shaft of diameter d is subjected to a torque T. the maximum normal stress induced in the shaft is O a. 32T/nd^3 O b. Zero O c. 8T/nd^3 O d. 16T/Ttd^3
ANALYZE THE STRUCTURE USING CONSISTENT DEFORMATION METHOD. DRAW SHEAR AND MOMENT DIAGRAM. المنيهللااال 7.5 mm 21 kN/m E = 20000 MPa 1= 1.61×106 samm 4.5m 1 с
Problem Set 1: A 6-m simply supported box beam is loaded as shown in the figure. Determine the maximum flexural stress in the beam. 30 kN 250mm 190mm 50 kN/m B 4m V V 2m 240mm 300mm
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 465 mm². Determine the average axial stress in each bar. 85 kN 56 kN 2 m D 1m 1 m E 1m 1m F LL
Example 24.4. Calculate the maximum torque that can be transmitted by a 35 cm diameter shaft if the twist in the shatt is not to exceed 1 degree in 15 diameter of length and also the shear stress is limited to 50 MPa. Take modulus of rigidity for the shaft material C = 85 GPa.
A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and the torques are T1 = 20 kip-in. and T2 = 6 kip-in. Calculate the shear stress at segment AB in ksi. Note Round up final answer to whole number T2 L.