5-78. The bent rod is supported at A, B, and C by smooth journal bearings. Compute the x, y, z components of reaction at the bearings if the rod is subjected to forces F = 300 lb and F, = 250 lb. F, lies in the y-z plane. The bearings are in proper alignment and exert only force reactions on the rod. n20 F1 45° 1 ft A 4 ft 5 ft 2 ft 3 ft- 30° 45° F2

Q: ness of the be 6 kN 2 m F 3 m A Owl

A:

Q: 6-79 The steel shaft has a circular cross section with a di- ameter of 2 in. It is supported on…

A: Step 1:Step 2: Step 3: Step 4:

Q: The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

A:

Q: 3. Determine the support reactions on the member shown below. The collar at B is fixed to the member…

A: Given, external force of 100 lb To determine, support reactions

Q: *4-12 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm².…

A: Sc= 0.0975 mmExplanation:

Q: 3- The beam - column below, which has two ends and Concentrated load Q-80 KN and compressive load…

A: Note : Since there are two questions given in a single question window. As per guidelines only 1st…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A:

Q: F9-5. The beam is subjected to the load at its end Determine the maximum principal stress at point…

A: Given : Determine the maximum principle stress at point B ? Concept -  Principle stresses are taken…

Q: Determine the force in member CG for the truss using the method of joints. 133 kN 67 kN B F G -4 at…

A: Given Data  Find the force in member CG (FCG) using method of joint.

Q: Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of…

A: Young's modulus of A-36 steel = 29007.5 ksiA point load of 10 Kip is applied at E.To determine the…

Q: The compound beam is fixed at A and supported by a rocker At B and C. There are hinges (pins) at D…

A:

Q: (Mc)y = -226 N-m The shaft is supported at its ends by two bearings A and B and is subjected to the…

A:

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A: Given:

Q: 4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is…

A: Displacement of b, δb​ =2.31 mmDisplacement of a, δa​ = 2.64 mmExplanation:

Q: Assume that the axial member is in equilibrium and the applied forces are an unknown load F1, F2 = 8…

A: Given ; F1 , F2 = 8kN F3 = 6 kN and F4 = 4 kN To find : Normal force at section B Normal force at…

Q: В 10in 10in D 1.5in 2in

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.