Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.75 in. If a force of 10 kip is applied to the bar, determine the angle of tilt of the bar. 2 ft B -1.25 ft- E D 0.75 ft F 10 kip 3 ft 1 ft Į

Q: For the truss shown, loads are transmitted to the bottom chord. Draw the influence diagram of member…

A: Maximum tensile force The maximum tensile load a body can sustain before failure divided by its…

Q: 2. For the structural beam shown; noting that the internal hinges lies in the midspan of the beams;…

A:

Q: Question 1: The blue bar AB is acted on by a couple moment. The green L- shaped bar BC is acted on…

A: madnitude of the triangle load =12×50×9=225 lblocation =23×9 =6 ft below Cmagnitude of UDL =32×8=256…

Q: 4.168 A slender, homogeneous, 20-ft rod weighing 64.4 lb is supported as shown in Figure P4.168. The…

A:

Q: equivalent resultant force and couple moment at point A. +103. Replace the loading system acting on…

A: to find resultant

Q: F8-9. Blocks A and B have a mass of 7 kg and 10 kg. respectively. Using the coefficients of static…

A:

Q: The bearings at A and D exert only vertical reaction on the shaft. The loading is applied to the…

A: A ) We are asked to determine : A ) The shear diagram for the shaft. B ) Draw the moment diagram…

Q: N 60 lb 50 lb 12" 10" -15" Problem 2 Figure 40 lb-ft

A: Resultant force =

Q: At what distance, "a" should the bearing supports at A and B be placed so that the displacement at…

A:

Q: RCES and DRAW THE SHEAR TELYOF the following beam COMPUTE THE MAXIMUM BENDING STRESSIN…

A: support reaction: ∑MB=0RA×3+4×3×32-12×4×3×33=0RA=-4 KN∑FY=0RA+RB-4×3-12×4×3=0-4+RB-4×3-12×4×3=0RB=22…

Q: The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD…

A:

Q: 7. The force F on the piston in Figure 5 causes the link AB to exert a force P = 2 kN on the pin B…

A: T

Q: 5-78. The bent rod is supported at A, B, and C by smooth journal bearings. Compute the x, y, z…

A: Introduction- A reaction force opposes an action force by acting in the opposite direction. During…

Q: Replace the loading by an equivalent resultant force and couple moment at point O.

A: The given data is shown below:

Q: Replace the loading by an equivalent resultant force and couple moment acting at point A.

A: Replace the loading by an equivalent resultant force and couple moment acting at point A.

Q: 4 Two plates (14 in x 2 in) are welded to an I-beam (W12 x 16). Find the moment of inertia with…

A: Width of plate (b) = 14 in  Depth of plate (d) = 2in W12 x 16 beam section    To find : Moment of…

Q: 2m 2m EN 6kN/m 4kN/m 2 TT C 377 1m 4m 6m termine the following: a. Moment at 1 or B (kN-m; write…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.