equivalent resultant force and couple moment at point A. +103. Replace the loading system acting on the post by an equivalent resultant force and couple moment at point B. 650N 500 N 30 300 N 1500 N- m Prob 102/103

Q: Determine the internal shear in kip at the distance 14 ft. from point A (it is the point between…

A:

Q: 3-4) A rectangular plate is supported by brackets at A and B and awire co. if the tension in the…

A: To determine: The moment about A of the force exerted by the wire on point C.

Q: The influence line is for V40 = shear just left of 40'. A load of 0.6 kip/ft is placed from 10' to…

A:

Q: Draw the shear and moment diabgram of the beam

A: ∑MB=0RA×3-12×15×3×23×3=0RA=15 kN ↑∑V=0RA+RC=12×15×3+2015+RC=12×15×3+20RC=27.5 kN ↑∑MA=012×15×3×13×3…

Q: *12-16. Determine the maximum sheur stress acting in the beam at the critical section where the…

A: Calculate the area of the beam section. The area of the beam section is A

Q: I 1-3. The beam AB is fixed to the wall and has a uniform weight of 80 lb/ft. If the trolley…

A: The internal loadings acting at any cross-section is the :Shear force, VBending moment, M

Q: Question 1: The blue bar AB is acted on by a couple moment. The green L- shaped bar BC is acted on…

A: madnitude of the triangle load =12×50×9=225 lblocation =23×9 =6 ft below Cmagnitude of UDL =32×8=256…

Q: The reaction at the support D of the continuous beam ABCD, hinged at two points shown in below…

A:

Q: A 늘- P 늘 B

A: A beam is given with a vertical roller at A and a horizontal roller at B.     To determine the…

Q: What will be the fully plastic moment in the portal frame shown in figure? The frame has a uniform…

A:

Q: The 30m long compound beam has an internal hinge at point E and is supported by pin C roller D and…

A: Sketch the free body diagram of the beam:

Q: F4-27. Replace the loading system by an equivalent resultant force and couple moment acting at point…

A:

Q: internal pin) osnimetabni to sobodenimsed ak-31 Gf lok.ft (e) 6ft. 6ft + Ay - Fytk 8k 2k/ft WY…

A: The figure is shown in the above figure. We have to find out the reaction at supports.

Q: Q2. Draw the influence line for (Rb, Re, Rf, Rg. Mp, Mm, and Mb) P A B C D mm n b E F mm b

A: Step 1: Step 2: Step 3: Step 4:

Q: 4-2. Determine the internal normal force, shear force, and bending moment at point C. Point C is…

A: Given Load 12 kN and 12 kN/mSpan 8 mConcentrated moment 24 kNmTo find out Normal force, shear force…

Q: 3.6 A 4-m-long rigid body carrying a 10-kN/m uniformly distributed load is supported by a pinned…

A: given data is length of bar=4m to find the free body diagram and the reaction force at A also to…

Q: Repeat Prob. 3-5 using singularity functions exclusively (including reactions).i want handwritten…

A:

Q: The gate AB shown below is ¼-circular and 1.5 ft wide (into the page), is pinned at A and rests on…

A:

Q: Find the force in bar CD using METHOD OF SECTIONS (hint: there is no need to find reactions). B с D…

A:

Q: *7-28. Railroad ties must be designed to resist large shear loadings. If the tie is subjected to the…

A: Consider the free body diagram of the given rail ties supporting the rail loads and ground reaction…

Q: F44. Determine the moment of the force about point O. Neglect the thickness of the member. 50 N -100…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.