# 45.A rectangular post which isglued to getheran anglemaae up oftwo boardsalonga joint inclinedat APニ45°Given:working stress for woodStress in glueso0 mpanormal130 mpaShearing stress in9 luesecti on of waod=150 mpa%3Deross35 cm メ 15 しmSolvefor largestaxial force p.

Answer: The largest allowable axial force P is 5250 kN.

45. A rectangwlar glue d to gether angle f two boards post whch is made up of a joint inclined along at AP an 45° ニ Given: for wood = in glue Shear ing stress in g lue = 100 mpa working Stress normal Stress 130 mpa 150 mpa 35 cm x 15 em evoss Secti on of wa∞d= SOve for langest axial force p.

45. A rectangwlar glue d to gether angle f two boards post whch is made up of a joint inclined along at AP an 45° ニ Given: for wood = in glue Shear ing stress in g lue = 100 mpa working Stress normal Stress 130 mpa 150 mpa 35 cm x 15 em evoss Secti on of wa∞d= SOve for langest axial force p.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring in the point.
Please don't provide handwritten solution .....
A slip collar with weight W = 150 pounds falls from a height h = 2 inch. Towards a flange located at the bottom of a vertical slender bar. The bar has a length L = 4 feet and a section area transversal A = 0.75 in2 and its modulus of elasticity is E = 30 x 106 psi. Calculate the following amounts: a) the maximum downward displacement of the flange b) The maximum tensile stress in the bar c) The impact factor.
Q.3. For figure Q3, find rivet diameter, where t = 100MPa ? 20mm O O 30mm 1909 20mm- 30mm Fig.Q.3 4 KN 25 550mm-
Please complete this question ASAP. This question doesn't have a diagram and I keep getting stuck. I need this done within an hour and a half. Thanks.
mm. NegiCOL UIC wOg VA vUampvuva 1.4-12 A rigid member DAC as shown in Fig. P1.4-12 carries the load P. Bar AB is an aluminum bar whose cross-sectional area is 0.5 in, and it is pinned at A and B by 0.5-in-diameter pins in a single-shear configuration. If the maximum allowable normal stress in AB is 7000 psi and the maximum allowable shear stress in the pins is 15,000 psi, find the maximum allowable load P. For aluminum E 10 x 10° psi. %3D 8 ft 7 ft P B Fig P1.4-12
Need Help With This Question
Q1// A hollow shaft of 10mm inside diameter and 5mm thick and 2m long extends by 0.5 cm under a tensile load (P) .find 1- the load P if E=2.10° N/cm? 2-the tensile stress in the shaft.
1.Calculate the axial force in rope J in N. 2.Calculate the elongation in rope K in mm. 3.Calculate the normal stress in rope L in MPa.
A rigid weightless be am SUPPorted at the point D by the pixed goint loo ded by the momend M is Support and points B and c holding the beam horisonta lly . a + the ver tical bs connected are For the data listed below determne ! Data > E = 2.1x10$ MPa gie ld stres 6y: 250 MPa , foctor oc Sofety Sr-1.S * Necessoy are a wetion A ? Of Cross - Other Data ; I 5 cM , a : U cm Ma SONM Safety · design method ond limit-state- mordatory. * Use both, Factorr design netled. Both net hats A.E 2A a
Handwritten solution with diagram Thanks
(c) The cross section of a quarter circular concrete block XYZof width 1.8m is shown in Figure 3. The specific weight of the concrete mix is 24 kN/m3. The hinge is along XX. Calculate the vertical force R at Y to hold the gate in this position. K Fixed slab 1.2 m Y W Fy 1.3 m FĦ D B Figure 3