A straight length of copper steam pipe 450mm long connects two components. Find the stress in the pipe if it is heated through 140 C and the expansion is limited to 0.8mm. The coefficient of expansion for copper is 1.7 x 105per degree C and the modulus of elasticity is 103 GPa.

A straight length of copper steam pipe 450mm long connects two components. Find the stress in the pipe if it is heated through 140 C and the expansion is limited to 0.8mm. The coefficient of expansion for copper is 1.7 x 105per degree C and the modulus of elasticity is 103 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Related questions

Q: O al- nd 3.40 Compute the moment of the force F about point A for the conditions shown. 60° F = 150…

Q: Find the residual forces acting in a truss with members AC=1000N (T), EG=520N (T), and FH= 1200N (C)…

A: Given AC=1000 N (Tensile) EG= 520 N (Tensile) FH =1200 N (Compression)

Q: The opening between a 3m long piece of steel and a rigid support is 1.5mm.As the temperature rises…

A: Given : L = 3 m = 3000mm Yield allowance δ = 1.5 mm dT = 25 ⁰ C α = 1.1 x 10-5 /⁰C NOTE :from…

Q: Use the relation for ideal work to calculate the minimum power needed to freeze a mass flow of 1…

A: Given data Mass flow rate Intinal Temperature of water is 21.1 ° CFinal Temperature of Ice is 0°C

Q: 2. Air is used in a Carnot cycle, the heat supplied is 75 kJ and the isentropic expansion ratio is…

Q: 1. In reinforcing a pressure vessel, which of the metal metal following is hoop strip correct? Why?…

A: Pressure vessel with metal hoops as a reinforcement is the best choice due to following reasons:

Q: 4. Helium at 149 kPa absolute and 10°C is isentropically compressed to one-fourth of its original…

A: Answer 4: Given data: P1=149 kPaT1=10°CV2=14V1 Need to determine the final pressure.

Q: 3. Determine the force in members DJ, CD, CJ and KJ of the truss which serves to support the deck of…

Q: Determine the tension in the cord and the acceleration of each block. Coefficient of friction…

Q: ference to the water flowing through the packed bed in Fig 3 for the water superficial velocity to…

A: Given:To find:Value of Reynold's number, .

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE STRESS A COMBINED STRESS?

A: The objective of the question is to understand why the ASME 31.3 allowable stress is a combined…

Q: 1. Problem Solving. Woite inside a Box. 1) Find the alliwable safe load p if the stresser in the bar…

A: Stress in bar AB, σAB=60ksi=413.685N/mm2Stress in bar BC, σBC=50ksi=344.738N/mm2Stress in bar CD,…

Q: 1. The 20kg cylinder and 50 kg cylinder are connected together using a rope that passes around a…

A: Givenmass of cylindermB=50kgmA=20kg

Q: Using the provided information, compete the following problems. • The system shown is in static…

A: Given:- = surface density of solar A = area The gravitational pulls…

Q: List some applications that use low-pressure piping

A: The low-pressure piping systems are used to carry nonhazardous materials that are used in Industry.…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

Q: According to ASME B.31, what is the value of Y (reduction coefficient) in the formula below (wall…

A: The objective of the question is to find the value of the reduction coefficient (Y) for austenitic…

Q: 6. Find Ix, ly, radii of gyration and product of inertia.

A: The schematic diagram of the given figure is Part 1 :- A triangle OAD whose sides are 100 and 300…

Q: Determine the Normal force and frictional force if coefficient of friction is 0.30.

Q: A one cubic meter tank of natural gas at 10 degrees Celcius weighs 100 N (ignore the weight of the…

A: The universal gas constant of natural gas i.e., methane is 518.28 J/kg.K. Write the ideal gas…

Q: Two blocks with masses m1 = 5 kg and m2 = 15 kg are connected by a rope as shown. The horizontal…

A: Answer: The speed of mass m2 after it has fallen by 6 m is 9.40 m/s2.

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

Q: A thick-walled pipe should be mounted in the space between a shaft and a wreath....

A: Given-Data:- Inner Radius =aOuter Radius =2av=1/2 To-Find:- Tension

Q: 18 Consider fully developed flow in a circular pipe with significant entrance effects. If the length…

Q: 1) A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi…

A: Given values are - T1 = 82°F =542°R , T2 = 74°F =534°RP1 = 300psi , P2 = 190psiVolume of cylinder V…

Q: A plank 25 meters long is placed on rough inclined planes at an angle of 15 with the horizontal as…

A: For Find the value of x, 1). first apply force equilibrium eqn. along the plank and find relation…

Q: 3. Find the absolute pressure in kPa at a depth of 10 m below the free surface of Oil of sp. gr.…

Q: The tangential stress is produced twice that of the longitudinal stress in thin walled pressure…

Q: Water is flowing through point 1 (D = 22mm) and point 2 (d = 17mm) in the above venture meter. What…

A: According to the given data D1=222mm D2=17mm Q˙=0.70zl/s We need to find P1-P2

Q: Magnetic Force on a Moving Charge A particle with a charge of -1.602 x 10 C is moving with…

A: formula: F = q(v ×B)

Q: 50 KN/m Determine the vertical deflection at the free end and the slope at the left support of the…

Q: hy there is a little amount of heat loss for fully covered insulated pipe compared to bare pipe?

A: To state the reason why there is a little amount of heat loss for fully covered insulated pipe…

Q: Explain the re guage

A: solution of above problem is below:

Q: apipe has an outer radius of 3.51 cm. if the metal is 0.22 cm thick, what is the inner diameter of…

Q: et, determine the amplitude and frequency of oscillation of the target

A: Need to calculate the amplitude & frequency of oscillation.

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

A straight length of copper steam pipe 450mm ...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical steel pressure vessel has a 700 mm inner radius and 15 mm thick walls. Find the change in the inner radius when the vessel is pressurized to 1.5 MPa. Use E= 200 GPa and Poisson's ratio= 0.3 for steel.
A wire of diameter 3 mm and length 4 m extends by 2.5 mm when a force of 10 N is applied. Find Young's modulus of material of the wire.
Please help me answer this asap. Thank you!!
A rubber ball is inflated to a pressure of 60KPa. At that pressure, the diameter of the ball is 230mm and the wall thickness is 1.2mm. The rubber has a modulus of elasticity of E = 3.5MPa and Poisson’s ratio of 0.45. (a)Compute the maximum tensile stress. (b)If the allowable tensile stress of the rubber ball wall is 2.5MPa, compute the internal pressure the rubber ball could be inflated.
A steel rod is stretched between two walls. At 20C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at 20C. find the minimum allowable diameter of the rod. Use 18/deg Celsius and E = 200 GPa.
Please show complete solution and box the final answer
A steel bar of cross-sectional area 200 mm^2 is loaded as shown in Fig. Find the change in length of the bar. Take E as 200 GPa. 50 kN 45 kN 35 kN 30 kN + 200 mm 300 mm 150 mm
A steel bar 2m long, 20 mm wide and 10 mm thick is subjected to a pull of 20 kN inthe direction of its length. Find the change in thickness. Take E-200 GPa and Poisson'sRatio 0.30
The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile stress is 3 times the lateral strain. Calculate the modulus of rigidity, bulk modulus and also find the change in volume when the bar is subjected to hydrostatic pressure of 150MPA. Take E = 150GPA.
The question is related to Modulus of rigidity and is attached as an image.
1. Steel rod 2.5m long is secured between tow walls. If the load on the rod is zero at 20°C, compute the stress when temperature drops to (-20°C). The cross-sectional area of the rod is 1200 mm a=11.7µ m/(m.°C) and E=200 GPa. Solve assuming (a) that the wall is rigid and (b) that the wall spring together a total distance of 0.500mm as the temperature drops. I
A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is 256GPA. Find the stress, Strain, and determine how much the column is compressed. Label the following diagram to show Stress, Strain, Tensile Strength, Yield Strength and Rupture Strength