4.3-5 Consider the beam with an overhang shown in the figure. (a) Determine the shear force V and bending moment M at a cross section located 5.5 m from the left-hand end A. (b) Find the required magnitude of load intensity q acting on the right half of member BC that will result in a zero shear force on the cross section 5.5 m from A. -5.5 m q= 4.4 kN/m 5.8 kN/m В 3 m - 3 m -1.8 m--1.8 m-

4.3-5 Consider the beam with an overhang shown in the figure. (a) Determine the shear force V and bending moment M at a cross section located 5.5 m from the left-hand end A. (b) Find the required magnitude of load intensity q acting on the right half of member BC that will result in a zero shear force on the cross section 5.5 m from A. -5.5 m q= 4.4 kN/m 5.8 kN/m В 3 m - 3 m -1.8 m--1.8 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 4-m span simply supported beam carries a uniformly distributed load of 45 KN/m over its entire length. The cross-section is as shown in figure. Determine the maximum bending moment along the length of the beam (in KN-m). Determine the maximum moment of area of the cross-section (in mm3). Determine the maximum shearing stress in the beam (in MPa). Determine the maximum shear force along the length of the beam (in KN). Determine the maximum bending stress in the beam. (in MPa).
Steel structure design
1. A 6.4 - m beam has a pin support at the leftmost part of the beam and a roller support located at 4 meters from the pin support. It carries a uniformly distributed load of 40 kN/m throughout its entire length. Using shear and moment diagram, A. Calculate the maximum shear. B. Calculate the maximum moment. C. Determine the most economical and lightest S-shape if the flexural stress is equal to 120 MPa. D. Calculate the actual bending stress of the chosen beam.
27 - Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed joint, the G point is the intermediate joint, and the B and C supports are the sliding joint. Loads on the beam P1 = 24 kN, P2 = 2 kN, q= 4 kN ⁄ m, beam dimensions a = 4 m, b = 2 m. Accordingly, Bx = ? a) 6B) 4C) 10.5D) None.E) 0
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m. Given: b = 110 mm and d 160 mm. 280 mm 150 mm
569
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 160 mm. 280 mm b. 170mm
A simply-supported beam with length, L = 10 m, is carrying a downward uniform load, w = 31 kN/m throughout its length. The cross-section of the beam is shown in the figure with a = 480 mm, b = 24 mm, c = 24 mm, and d = 177 mm. Determine the maximum flexural shear stress in MPa. 19 a tot a fof d *
A simply supported beam 4 m long has a croSs section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 180 mm. %3! 270 mm 160 mm
3.75 pts For the shown figure, member BC has a square cross section and the applied load P at point Cis 45 kN. Find 5 kN/m the length of the cross-section side that is required to ensure that the developed shear stress at section a-a is D not allowed to exceed 120 MPa. AB = 4 m, AD = 2 m, AC =3 m. o 11.772 mm O 6.697 mm O 15.546 mm B. O 10.828 mm Next
G=5 M=9 Given: 25 kN and 18 mm