Answered: Determine the maximum uniformly…

Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The span length of the cantilever beam is L = 4 ft. Determine the magnitude of the maximum bending stress in the pipe. O 21.55 ksi O 13.81 ksi O 15.73 ksi O 24.04 ksi O 17.18 ksi L B P d Pipe cross section. D
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
Need help ASAP Determine the max flexural stress in MPa
A simply supported wood beam that is 14.1 m long carries a 47 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 360 mm, a = 70 mm, andc = 20 mm. Section a-a is located at x = 2.4 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. y H a a A В K L 2L Answer: (a) TH = i kPa (b) TK = i КРа (c) Tmax = i kPa (d) Omax MPa i 13
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa
8
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64 MPa. 150 mm Determine: the minimum width for the beam 6 m b
A simply supported wood beam that is 9.3 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 160 mm, d = 400 mm, a = 80 mm, and c = 30 mm. Section a-a is located at x = 1.6 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P y H a A a B C 2L 3 Answer: (a) TH = i kPa kPa (b) TK = i kPa (c) Tmax = i MPa (d) Omax= i
Subject: