Determine the threshold torsion

Q: Question 11 of 12 - / 1 Current Attempt in Progress A 33 mm by 33 mm square ABCD (i.e., a = 33 mm)…

A: In this problem, we are given a square that is deformed into a rhombus due to the application of a…

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: The hoop stress and the radial pressure variation can be obtained using Lame's equation:

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-320 MPa Normal stress in Y direction σY=240 MPa Shear…

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

A:

Q: buoyant force acts in the direction opposite the force of

A: Buoyant force is the upward force exerted by fluid on object when it is submerged fully or partially…

Q: 7. With the boundary layer separation, displacement thickness a) Increases b) Decreases c) Remains…

A: With the boundary layer separation, displacement thickness a) Increases b) Decreases c) Remains Same…

Q: Steel railroad reels 15 m long are laid with a clearance of 5 mm at a temperature Ti = 49 °C. Assume…

A: Following are the given data. Length of railroad reel, L=15 m Clarence, C=5 mm=0.005 m Temperature,…

Q: b 1- Shear failure occur when oz Oh > oy OH > Oy > oh Oy > OH > Ơh 5- Tensile Failure Vertical…

A: Brief concept introduction- Shear failure- It occurs when the shear stress developed in the…

Q: Internal static analysis has both advantages and disadvantages.

A: Concept- Internal static analysis- Static analysis is an examination of the application's internal…

Q: Shear Stress W= 1o EN/m 6. 5m T ? 2. Ta

A:

Q: Create a 2D contour plot to allow the performance of the structure to be assessed against the…

A:

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=560 MPa The value of normal stress in Y…

Q: Show the type of stress distribution over the radius of the disk 3. How is the correspondence…

A: The area of the middle section of the rod is reduced with respect to both ends which means the disk…

Q: 30kg and ma= 70 kg. Between all of the contacting swrfaces, u, = 0.1. What is the largest force F…

A:

Q: ver a length of 1 m. induced is 120 N

A:

Q: horizontal pipe, which of the following is constant? Pressure head Elevation head Velovity head

A: In horizontal pipe, pressure head, elevation head and velocity head all will be constant { however…

Q: 200KN 200 ku

A:

Q: Solve the given initial value problem. w" - 4w' + 2w = 0; w(0) = 0, w' (0) = 1 %3D %3D

A: solution given in next step

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: Given- Inner dia DiOuter dia DoInternal fluid pressure =pcircumferential tensile stress=py

Q: Steel railroad rails 10 m long are laid with end-to-end clearance of 5 mm at a temperature of 18°C.…

A:

Q: 1. The beam ABCD with a rectangular cross section caries the loading shown in figure. Determine (a)…

A:

Q: Describe FIVE (5) basic assumptions upon the application of the Bernoulli equation. (a) A pitot tube…

A:

Q: Determine the deflection at the end of the overhang by conjugate beam method or Castigliano's…

A:

Q: Determine maximum principal stress

A: Given data : The value of normal stress in X direction σX=150 MPa The value of normal stress in Y…

Q: : Calculate and sketch the normal stress distribution acting over the cross section at section a-a.…

A:

Q: 85 MPa B 66 MPa 65° 28 MPa A

A: We will use equations for principal stresses.

Q: Consider a beam with loading and cross-section as shown below. 10 kN/m + 200 mm 5 m Rectangular 400…

A: Given data:

Q: Taking 'k' components 0. 77TEC + 0. 8TBD=1440. -(1) Taking 'j' components 0. 514TEC – 1.6TBD=0.….…

A:

Q: 60 MPa 70.4 MPa 36.4 MPa

A:

Q: Transformations (strain) Q43 A strain guage rosette is placed on the outside surface of a loaded…

A: Given data  εx = 578 microstrain  ( at θ = 0°) εy = 947 microstrain ( at θ = 90° )  εx' = 57…

Q: A thin-walled tube is subjected to torsion as shown. Determine the Perimeter of the median line, S.…

A: t=25mm L-6m r-300mm θ=80o T=4 kNm G=70 kN/m2 S-Perimeter?

Q: Another way of testing flexure strength is by quarter point loading as shown. The sample section is…

A:

Q: QIDiscuss in detail the effect of the boundary condition in the Buckling of hollow shaft.

A: when boundary condition changes ,effective length of hollow  shaft also changes and hence euler…

Q: Determine stress

A: Given data Load =P=30 KN Area=A=20 mm 2  Determine stress =?

Q: The thin square plate shown is uniformly deformed such that , +1.360 ut. , -628 ut, and y=+1.285…

A:

Q: State the determinacy of the beam shown. Answer is: Unstable. Show solution

A: To find degree of static indeterminacy of beam

Q: get. The shear stress at a point in a liquid is found to be 0.03 N/m². The velocity gradient at the…

A: Given data : Shear stress (ζ)=0.03 N/m2Velocity gradient dudY=0.15 s-1

Q: 1. A circular flat plate of diameter 120 mm and thickness 10 mm is constructed from steel with E =…

A: Given values: Circular plate, diameter, d = 120 mm thickness, t = 10 mm E = 208 GN/m2 Uniform…

Q: 78.75 мра 33.61 MPa 22.11 MPG Determine @ Omax Omin Tmax (@s, @p) sketch the result JLULL e pain…

A: