Draw the bending moment diagram of a continuous reinforced concrete rectangular beam shown by Method of Consistent Deformation. Assume El to be constant for all members and E = 200 GPa, 1= 8x106 mm*. 3 kN/m E 1.5m 1.5m 3m 2m El is constant

Draw the bending moment diagram of a continuous reinforced concrete rectangular beam shown by Method of Consistent Deformation. Assume El to be constant for all members and E = 200 GPa, 1= 8x106 mm*. 3 kN/m E 1.5m 1.5m 3m 2m El is constant

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
SHOW SOLUTION AND ILLUSTRATION
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
A beam 2.4 m long is simply supported at two points A and B which are 1.44 m apart; point A is 0.36 m from the left-hand end of the beam and point B is 0.6 m from the right-hand end; the value of EI for the beam is 240×10® Nmm². Find the slope at the supports due to a load of 2 kN applied at the mid-point of AB. Use the reciprocal theorem in conjunction with the above result to find the deflection at the mid-point of AB due to loads of 3 kN applied at each end of the beam. Ans. 0.011, 15.8 mm.
Rhelp**
Find the normal stress, shear stress, and bending deformation of the beam. For the cross-sectional area: by = 0.75 meter, d = 1 meter, tw = 0.10 meter, and tf = 0.15 m.
The cantilever beam shown in Figure A is subjected to load magnitudes of Pz = 3.0 kips and Py = 8.1 kips. The flanged cross section shown in Figure B has dimensions of bf = 7.1 in., tf = 0.55 in., d = 11.5 in., and t = 0.35 in. Using L = 70 in., determine: (a) the bending stress at point A. (b) the bending stress at point B. (c) the angle for the orientation of the neutral axis relative to the +z axis. Note that positive angles rotate clockwise from the+z axis. FIGURE A P₂ L B tw bf D FIGURE B
Part of a two story building is shown in the figure in which a concerte column and a steel column are used in the first and second floor. The compressive force on the roof of the second floor is PC = 400 kN. The compressive force on the first floor is PB = 310 kN. The steel [Esteel = 200 GPa] column is a wide angle steel shape that has a cross section area of A2 = 1850 mm2. The concrete [Econcrete = 30 GPa] column has a circular section with a diameter of d = 530 mm.[L1 = 4.8 m, L2 = 5.8 m] What is the displacement of the column at B?in mm What is the displacement of the column at C? In mm