4. Doors Lite is called rail door? 5. Composite beams are constructed from steel and timber? 6. The set of sills with a section of iron, which bears high loads, is called Girder? 7. Granite is used to cover bathroom floors? 8. PVC is used for basement and garage floors? 9. In one-way slab there is main reinforcement in two directions? 10. shell roof is relatively thin and does not require support beams?

4. Doors Lite is called rail door? 5. Composite beams are constructed from steel and timber? 6. The set of sills with a section of iron, which bears high loads, is called Girder? 7. Granite is used to cover bathroom floors? 8. PVC is used for basement and garage floors? 9. In one-way slab there is main reinforcement in two directions? 10. shell roof is relatively thin and does not require support beams?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q4/ Complete the following statements as appropriate a- The amount of steel reinforcement is calculated according to the following formula b- The approximate estimation is c- Duration of maintenance is d- Electrical work calculate in e- The form area for the beam equal
Give me right answer with short explanation... Urgent Thank you
Designers typically specify longitudinal reinforcement on all four sides of a square column cross section for which of the following reasons? Check all that apply. Bending moments can act about two section axes, not just one O There is less chance for steel placement mistakes during construction There is additional axial strength compared to a design with longitudinal steel on only two sides
1- 3 defects of hollow walls. 2- The number of 3 reasons for the collapse of scaffolding during casting, and what are your procedures as an engineer to prevent this problem? 3- If the standard metal sections available in the local market cannot bear the load imposed on the construction beam, what will you do with the solution provided? 4 - 3 Features of Flat Concrete Ceilings
B) For reinforced concrete lining, the transverse reinforcement is two times the longitudinal reinforcement.O FalseO True
10. A simply supported beam 300 mm wide, 500 mm deep and spans 5.0 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness is 200mm. Note: 1-Standard bar hook-(12db+4db) with bend. Answer should be made such as table below from bar No.1 to bar No.8 Bar No. Length (m) Weight(Kg) -4.70m- 2 opening (7) (4) 3.70m 400mm 8 6 Determine quantity of Steel in Kg for the Circular Sky-light in the figure above. Determine quantity of items below for given roof Figure above Concreter rate (1:1.5:3). y sand= 1835 kg/m³, y gravel = 2200 kg/m³ Item Unit Quantity Cement m3 Sand ton Gravel m3
I need the answer to the question in reinforced concrete
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
A singly reinforced rectangular beam has a dimension b 310 mm and d = 410 mm Factored moment is equal to 100 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 275 MPa and the reduction factor is 0.9. Determine the required steel area in mm?
What is the Design Bending Stress, Om,y,d in a joist, if the strength grade is C16
A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f'c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.