4-The air inside an electronics package housing has a temperature of50°C. A "chip" in this housing has internal thermal power generation(heating) rate of 3 X 10³ W. This chip is subjected to an air flowresulting in a convective coefficient h of 9 W/m2.C over its two mainsurfaces which are 0.5 cm X 1.0 cm. Determine the chip surfacetemperature neglecting radiation and heat transfer from the edges.Ans(T, 53.33C).

Answered: Image /qna-images/answer/bdf8ea41-7316-4eae-8988-7478293e8030.jpg

Answered: 4-The air inside an electronics package…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Plate glass 5 mm thick at 200°C is to be cooled from both sides using air at 40°C. If surface cracks are to be avoided, determine the maximum value of convective heat transfer coefficient. Material properties are density = 2500 kg/m3, = specific heat 670 J/kgK. Thermal conductivity 0.744 W/mk. Also determine the time required in this to cool the plate to 80°C. o 12:03
Air at 20°C flows over a plate which is at 80°C and temperature at a location of 0.5mm from surface is measured to be 50°C. Assuming themal conductivity of fluid as 0.025W/mK, the local convective heat transfer coefficient will be (A) 25W/ m²K (B) 30W / m²K (C) 35W/ m²K (D) 40 W / m²K
An electric resistance heater is embedded in a long cylinder ofdiameter 30mm. When water with a temperature of 25 C and velocityof 1m/s flows crosswise over the cylinder, the power per unit lengthrequired to maintain the surface at a uniform temperature of 90 C is28kW/m. When air, also at 25 C, but with a velocity of 10m/s isflowing, the power per unit length required to maintain the samesurface temperature is 400W/m. Calculate and compare the convectioncoefficients for the flows of water and air.
14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.oC) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: a. 361.7 W b. None of these c. 261.7 W d. 303 W
14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.0C) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: Q2 a. 361.7 W b. None of these c. 261.7 W d. 303 W
Small potato balls of 0.5 cm radius (can be approximated as a sphere) baked in the oven and initially at a uniform temperature of 160°C. Assume, potatoes have a density of 650 kg/m, specific heat of 3400 J/kgK and conductivity of 1 W/mK. You want to eat potatoes quickly without burning your tongue so that you have decided to cool them down with forced convection. Air h, T. hot potato initially Air temperature is 20°C and the convective heat transfer coefficient is 140 W/m?K. Calculate the time (in seconds) required for its surface temperature to drop 90°C.
Thermal jackets are typically put on cryogenicstorage tanks to minimize the heat transfer gainsfrom the surroundings. Consider a cylindercontainer that is 1.5 m long made from steel (k = 750W/m.K) with an inner diameter of 0.5 m and outerdiameter of 0.7 m. If the liquefied natural gas (LNG)inside the cylinder is maintained at 90 K, ambientconditions are Tamb = 20 °C, h = 7 W/m2.K. What is the required insulationmaterial to maintain the outer temperature of that jacket of 15 °C? Usethe end of the book and write your assumption with the right value.(Take a maximum allowed jacket thickness of Lins = 7 cm)
PROCESS INSTRUMENTATION AND CONTROL 4. A 3m X 2m window has an exterior surface temperature of 220C, and the outside wind is blowing air at -60C across it with a convection heat transfer of h= 125W/m2K. What is the total heat transfer loss?
Example of engineering application using Convection heat transfer. And draw a diagram of convection heat transfer. Note: Agricultural Machines only.
I need handwritten or I'll dislike

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS