300 N- m 200 N- m 48 mm 0.9 m 44 mm Elektrik motoru sabit bir hızla dönerken 1.2 m ABCD şaftına 500 Nm'lik bir tork 40 mm uygulamaktadır. G= 27 GPa olduğuna 1m B ve C kasnaklarına şekilde ve gösterilen torklar uygulandığına göre B ve C arasındaki burulma belirleyiniz. Formüller: açısını F.L , AL = a.L.AT, AL = A.E F O = E.E, 8= A AV T.L T.p G.J J 8, =lo, -v(0, +0,), a =-4, M. F y. o =- I O =-- s A

300 N- m 200 N- m 48 mm 0.9 m 44 mm Elektrik motoru sabit bir hızla dönerken 1.2 m ABCD şaftına 500 Nm'lik bir tork 40 mm uygulamaktadır. G= 27 GPa olduğuna 1m B ve C kasnaklarına şekilde ve gösterilen torklar uygulandığına göre B ve C arasındaki burulma belirleyiniz. Formüller: açısını F.L , AL = a.L.AT, AL = A.E F O = E.E, 8= A AV T.L T.p G.J J 8, =lo, -v(0, +0,), a =-4, M. F y. o =- I O =-- s A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the magnitude of force of AB is 100 N, what is the component along the y-axis (in Newton)?
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15900 ksi] rods, and a solid steel [E = 30300 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 28 kips is applied. (1) L2 (1) B P. Answers: i 27.744 ksi. 02 = 4.512 ksi.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13700 ksi] rods, and a solid steel [E = 32600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.84 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.5 in. Assume L1=37 in and L2=66 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 27 kips is applied. (2) (1) L2 (1) L1 A P
The 9-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m 0 B HA 2 m 50 N·m 1 of 1 Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. A= [5] ΑΣΦ ↓1 vec 1 Submit Provide Feedback Request Answer ?
1. A 200mm x 300mm beam has a simple span of 8 meters. It is necessary to place a support at midspan because of the excessive deflection at the center in order to limit the deflection to 12mm and such that the moment at that point is zero. E = 13,800 MPa. a. Determine the load carried by the beam. Express your answer in N/m. b. Compute for the reaction at the support at midspan so that the beam will not deflect at its midpan. c. Find the bending stress of the beam so that it will not deflect at its midspan. W- N/m 4m Pz 200 mm RI 300mm
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
This subject is Statics of Rigid Bodies. Show your solution
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
The central rod CD of the set below is heated from T1 = 30ºC to T2 = 180ºC by an electrical resistance. At the lowest temperature, the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel and each have a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Use EFe = 200 GPA, EAl = 70 GPA, αFe = 12 x 10-6 /°C, and αAl = 24 x 10-6 /°C. answer: 5.4 kN
1.) 600 lb Determine: 900 lb - The resultant force (R) - The angle 0 between the R and the x-axis 40 35°
The 5.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m- 0 B 2 m 50 N·m 1 of 1 Part A Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. 0 = for Part A for Part A for Part, A for Part A undo for Part A redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A Submit Provide Feedback Request Answer Next >