Two rods vertically connect beams AB and CD as shown in the figure. Point A is fixed supported while point D is hinged connected. If the rod on the right is heated by 18 degree Celsius,2 m-- 2 mA2 mCUse E = 200 GPa, linear of coefficient expansion = 11 7x 10 per degree celsius and A = 4500 mm2Compute for the deformation of the right rod in mm.Select the correct response0.0468 mm0.117 mm0 0234 mm0.0842 mm

Answered: Image /qna-images/answer/98d909cd-957d-41b2-b649-d15cd651089d.jpg

Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while point D is hinged connected If the rod on the right is heated by 18 degree Celsius, 2 m + 2 m A 2 m Use E = 200 GPa, linear of coefficient expansion = 117x10 per degree celsius and A= 4500 mm Compute for the deformation of the right rod in mm. Select the correct response 0.0468 mm O 0117 mm 0 0234 mm 0.0842 mm

Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while point D is hinged connected If the rod on the right is heated by 18 degree Celsius, 2 m + 2 m A 2 m Use E = 200 GPa, linear of coefficient expansion = 117x10 per degree celsius and A= 4500 mm Compute for the deformation of the right rod in mm. Select the correct response 0.0468 mm O 0117 mm 0 0234 mm 0.0842 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooled? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. roblem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D• A
A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross sectional area of 1cm?; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm? Determine the stress in the rods it p = 6 tonnes.
An Eccentric force P is applied as shown in the figure below
NOTE: PLEASE SOLVE THIS QUESTION WİTH FINITE ELEMENT METHOD...solve 20 mins asap hand written
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Refer to the photo provided and please make sure your handwriting is readable. Both wires have a cross sectional area of 17 mm2 and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible.
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
Situation 10: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress-free. The temperature in the steel rod is decreased by 40°C. Neglect the weight of the bar Steel L = 910 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/C AT = -45°C 0.5 m + 1.3 m Aluminum L = 1320 mm A 1200 mm² E = 70 GPa a = 23 x 106/C 27. Determine the stress in the aluminum rod 28. Determine the stress in the steel rod 29. Determine the deflection at the point where aluminum rod and bar is attach
278. A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. P-278. If the system is initially stress-free, determine the temperature change that will cause a tensile stress of 60 MPa in the steel rod. -2 m 2 m 3 m 3 m Bronze A-1200 mm² E 88 GPa x = 18.9 pm/(m. °C) Figure P-278. Steel A = 900 mm? E = 200 GFa Q- - 11.7 m/(m. °C)
When laying tracks for the railroad, a small gap & is left between the ends of the rails for thermal expansion. The gap is such that if the temperature increases from -20°F to 90°F the rails will just touch. If the temperature is increased to 110°F, what will be the axial force in the rail with a length L=50 ft, modulus of elasticity E=29x10ʻ psi, coefficient of thermal expansion a=6.6x106/°F, and a cross-sectional area of 5.2 in?. -8 -L ft