A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is KN-m A 3.82 B 1.18 (C) 2.64 D 0.48 E 5.03

A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is KN-m A 3.82 B 1.18 (C) 2.64 D 0.48 E 5.03

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A laminated plastic beam of square cross section is built up by gluing together three strips, each 20 mm x 60 mm in cross section (see figure). The beam has a total weight of 4 N and is simply supported with span length L = 400 mm. м 20 mm 20 mm 60 mm 20 mm 60 mm Considering the weight of the beam (q) calculate the maximum permissible CCWW moment M that may be placed at the right support. (a) If the allowable shear stress in the glued joints is 0.3 MPa. Round to the nearest tenth. Mmax =| N-m (b) If the allowable bending stress in the plastic is 8 MPa. Round to the nearest hundredth. Mmax N.m
Both ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T must be applied so that the reactive torques at A and B are equal. L L 2 2 0.75d A В T a -
/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPA, xst= 12(10)-6 600 mm 400 mm 50 kN 40 kN B C 50 kN
600 -400- 600 800 G| P2 P3 E F Tha at y pnywty i A - 100 mm E - 200 GPa A- 150 mm E- 200 GPa A130 mm E- 70 GPa 700 A- 50 mm E- 83 GPa P1 d. 30° o B 500 All dimensions are in millimeters.
Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. 1.) The reaction @ point D 2.) The tension @ Cable BE. 3.) The x-component of the reaction @ A. 4.) The y-component of the reaction @A 5.) The reaction @ A.
1. A beam is supported by two springs as shown below. The spring at A has spring constant KA = 200000 N/m while the spring at B has spring constant kB = 400000 N/m. The beam is loaded by a uniform distributed load of 500 N/m and a point load at C of 1000 N. 1000N A 500 N/ I ка 2M 1 SB ufi L кв экім- a. Assuming the beam is RIGID, calculate the deflection at point C. b. Assuming the beam is DEFORMABLE with EI = 200000 N-m², calculate the deflection at point C.
A beam has a L = 15 m and is carrying two points loads Load B- 7 kN and Load D- 4 kN applied as shown below. Load B Load D A E B D уз — уз * L/3 RA RE a) Calculate the reaction at A. R. kN b) Calculate the reaction at E. Re kN c) Calculate the bending moment at B. Mg kNm d) Calculate the bending moment at C (at the centre). Mc kNm
10
Q1/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPA, xst= 12(10)-6 600 mm 400 mm 50 kN 40 kN В C 50 kN
9
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 51 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 78 MPa. If a torque of Tc = 25700 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = i √₂ = i (2) с B A mm mm
Problem propeller shaft for a small yacht is made of a soli steel bar 104 mm in diameter. The allowable stre shear is 48 MPa, and the allowable rate of twist i: 2.0° in 3.5 meters. Assuming that the shear modulus of elasticity is Tmax 80 GPa, determine the maximum torque can be applied to the shaft. T 本