Two identical metal sheets are formed into tubes with circular and square cross sections shown. If the same torque is applied to each tube, determine the ratios (a) Tcircle/Tsquare of the shear stresses; and (b) Ocircle/Osquare of the angles of twist. 2 et

Two identical metal sheets are formed into tubes with circular and square cross sections shown. If the same torque is applied to each tube, determine the ratios (a) Tcircle/Tsquare of the shear stresses; and (b) Ocircle/Osquare of the angles of twist. 2 et

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
A rigid bar ABCD is supported by two bars as shown in Figure below. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (1) is 590 µ. Determine: a. The normal strain in bar (2). b. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin C before the load is applied. c. The normal strain in bar (2) if there is a 1 mm gap in the connection at pin B before the load is applied. (2) 1,500 mm 240 mm 465mm 140 mm Rigid bar B C 900 mm (1) P.
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
Either all parts or none.... I vll upvote definitely
P = 300N ، a=140mm , b=240mm , d=26mm
Solve it