Consider shaft AB that is fixed at point A and free at point B that is subjected to the torque T. The shaft is made of a tightly bonded core and outer shell. The core is made of Material X and the outer shell is made of Material Y. The polar moments of inertia of the shell and the outer core are equal. If the modulus of rigidity of Material X is higher than that of Material Y, which of the following is TRUE regarding the shear STRESSES at the INTERFACE of the two materials? Select one: O a. The stress at the interface on Material X is higher than that in Material Y Ob. The stress at the interface on Material X is lower than that in Material Y Oc. The stresses at the interface on Material X and in Material Y are both zero O d. The stress at the interface on Material X is equal to that in Material Y (both nonzero)

Consider shaft AB that is fixed at point A and free at point B that is subjected to the torque T. The shaft is made of a tightly bonded core and outer shell. The core is made of Material X and the outer shell is made of Material Y. The polar moments of inertia of the shell and the outer core are equal. If the modulus of rigidity of Material X is higher than that of Material Y, which of the following is TRUE regarding the shear STRESSES at the INTERFACE of the two materials? Select one: O a. The stress at the interface on Material X is higher than that in Material Y Ob. The stress at the interface on Material X is lower than that in Material Y Oc. The stresses at the interface on Material X and in Material Y are both zero O d. The stress at the interface on Material X is equal to that in Material Y (both nonzero)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve it
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young's modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work. (а) (b) Based on Q2(a), suggest an appropriate steel bar measurement.
8 Expansion is an axial deformation. 9 True 10 False The coordinates of centroid locate the ge ometric center of the cross-section of the material.( True False Torsional stress is also known as bending stress.( True False
The state of stress at a point in a member is shown on the element. Determine the absolute normal stress component acting on the inclined plane AB in ksi.
Solve the bending stress about points A and B
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
-, Try to find the overall stiffness matrix of the structure shown in the figure. The elastic modulus of the cross-section is E, the cross-sectional area is A, and the moment of inertia of the cross- section is I. (1,2,3) (4,5,6) (4,5) 3 (0,0,0) (0.0) 1
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
A bar in the shape of a solid truncated cone of circular cross-section is situated between two rigid supports which constrain the bar from any change of axial length. The temperature of the entire bar is then raised by AT. Assume that the cross-sections perpendicular to the longitudinal axis of symmetry remain plane and neglect localized end effects due to the end supports. Determine the normal stresses at any point in the bar.
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
The given stresses are 0x = 48 MPa, 0x =- 32 MPa, and Txy = 20 MPa. The rotation angle 0 = 30°.Use the stress transformation equations to determine the stresses on an element that is rotated bythe given angle 0 and show the calculated stresses on the rotated element.