300 mm x 500 mm simply supported rectangular beam has a span of 4.50 M. Concrete cover is 50 mm. It carries a uniformly distributed Dead Load of 15 Kn/M (incl. its own weight) and a Live Load of 10 Kn/M. fc’ = 24.15 MPa; fy = 275 MPa.   a. Find the maximum factored moment of the beam. b. Determine the required tension steel area. c. Find the no. of pcs if 25mmØ is to be used.

Q: G F E Problem #2: 4 ft - 4 ft 4 ft -4 ft- 450 + Y (Ib) 500 + Y (Ib) 550 + Y (Ib) 11. Determine the…

A:

Q: A beam with a span of 7.0 m between supports has an overhanging extended part of 2.0 m on one side…

A: Given: DL = 30 kN/m LL = 18 kN/m Factored load: Wu=1.2DL+1.6LL=1.230+0.618Wu=64.8 kN/m

Q: A reinforced concrete beam has a width of 300mm and an effective depth to tension bars of 600mm.…

A: width=300mm effective depth to tension bars = 600mm Compression reinforcement if needed will be…

Q: Q: Design a base plate for the column W s x 67, which is carried an axial compressive service load…

A: Geometrical properties of the base plate. Calculate factored loads on the column. Find the area.…

Q: For the beam shown, 3V a. draw SFD and BMD, b. prove that for the isosceles, Tmax. = bh C. if Ball =…

A:

Q: A reinforced rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1 layer…

A:

Q: A beam with a apan of 6m between supports has an overhanging extended part of 2m over the right…

A:

Q: From the given figure below, determine the maximum flexural stress of the beam if it has a cross…

A: Determine the maximum flexural stress of the beam?

Q: The beam AD is carrying a linearly varying distributed load as shown below. The beam is supported by…

A: Given data5 member steel truss is givenFind1) maximum shearing stress in the pin at connection…

Q: What is the maximum absolute shear for the following beam and load group? Use L = 20, a = 4, b = 3,…

A: Maximum absolute shear in the beam. Given, P1 = 4 P2= 2 P3= 3

Q: ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD. COMPUTE: RECUNDED. AXIAL LOAD OF AD AINT ALL MOMENT…

A:

Q: Column ABC has a uniform rectangular cross section with b = 12 mm and d = 22 mm. The midpoint C of…

A: Given : b = 12 mm d = 22 mm Centric load P = 3.7 kN FOS = 3.3 E = 200 GPa This is a problem of…

Q: A wood beam with a cross section 4 x 6 in. is simply supported at A and B. 4 in. ( -4 in.- Section…

A:

Q: A beam with S = 1,050 x 103 mm3, carries uniformly distributed load W1 and a concentrated load P1.…

A: Given  Flexural stress, σmax=145 Nmm2Sectional modulus,…

Q: P. A 2b This beam has a pinned support at the left end at A and a roller at the right cnd at B.…

A:

Q: The signboard truss is designed to support a horizontal wind load of 850 lb. If the resultant of…

A: To determine the force in members BG and BG.   In order to determine the force in said members we…

Q: A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed…

A: Answer  Width b = 300 m Overall height h = 600 mm Beam span L = 6 m Superimposed dead load = 30 KN/m…

Q: What is the maximum absolute shear in the following beam? Use L = 22, a = 3, b = 3, P₁=2, P2=5, and…

A:

Q: A simply-supported I-beam is subjected to three 5 kip loads as shown below. The beam is made from…

A: Determine the maximum shear stress developed in the glued joints.

Q: 5. A beam has a width of 300mm and effective depth of 540mm. d 60mm. It is reinforced with 8-25mm…

A:

Q: What is the maximum absolute shear for the following beam and load group? Use L = 18, a = 3, b = 3,…

A:

Q: P B L 3 in. The largest allowable length Lis -18 3 in. 4 in. ft.

A:

Q: A simply supported beam 300mm x 500mm has a span of 5m. The beam is reinforced with unbonded…

A: simply supported beam : A simply supported beam is one that is supported by only two points and can…

Q: A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported…

A: Given - Floor load of 750 N/m2 A = 11,500 mm^2 d = 350 mm; tw =  10 mm bf = 250 mm; tf = 16 mm Ix =…

Q: 4. A beam has a width of 300mm and effective depth of 540mm, d' 60mm. It is reinforced with 4-25mm…

A: A beam is defined as a horizontal structural element to resist vertical or laterally applied loads.…

Q: Determine the weight of 8m simply supported 200mm x 500mm rectangular beam whose allowable flexure…

A: Given data,  Width of beam = 200 mm Depth of beam = 500 mm Stress in beam = 22 MPa.  L = 8 m To find…

Q: If the maximum allowable force (tensile or compressive) in members BC in the truss shown known to be…

A: Option C is correct ( P= 36 KN )

Q: The frame shown is subjected to lateral loads acting at I and E. Assume all columns have the same…

A:

Q: #1 Consider the compound beam shown. Suppose that P₁= 1000 N, P₂ = 1600 N, w = 600 N/m and point E…

A:

Q: What is the maximum absolute shear for the following beam and load group? Use L = 19, a = 4, b = 3,…

A: you can clearly understand if you follow the below solution

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A:

Q: What is the maximum absolute shear in the following beam? Use L = 22, a = 3, b = 3, P₁ = 4, P2 = 4,…

A:

Q: The beam CD is rigid and it rests on two posts as shown. Both posts are made of steel and have a…

A:

Q: Calculate the ultimate moment capacity of the beam whose width is 400mm and effective depth d = 700.…

A: Given:Beam width, b=400 mmEffective depth of the beam=700 mmsteel area in compression =1953 mm2steel…

Q: F9-5. The beam is subjected to the load at its end Determine the maximum principal stress at point…

A: Given : Determine the maximum principle stress at point B ? Concept -  Principle stresses are taken…

Q: A rectangular concrete beam has a width of 300 mm and an effective depth to bottom bars of 430 mm.…

A:

Q: What is the shear force in member NC?

A: Shear force: - It is defined as unaligned forces due to which one part of body pushes in a specific…

Q: 1. Compute the moment capacity of concrete in kN-m. 2. Compute the moment capacity of steel in kN-m.…

A: 1. To compute the moment capacity of concrete in kN-m, we need to first determine the concrete…

Q: H "b" kN G "e kN

A: I will give only first part of the answer. Because second part is so lengthy an end it is not…

Q: Exercise No. 1: Draw the shear and bending moment diagrams for girder AB. Also determine the maximum…

A: The algebraic total of all the forces operating on either side of the section is known as the shear…

Q: A simply supported beam 300mm x 500mm has a spa unbonded tendons. fse = 750 MPa, Aps = 1200m above…

A:

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A: Step 1:Step 2:Step 3: Step 4:

Q: The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. 4 ft B A 3 ft D 3 ft C If…

A:

Q: The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi;…

A:

Q: A. Determine the depth of the compression block. (mm) B.Determine the nominal moment strength (kN-m)

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.