3. What is the resulting factor of safety in a solid steel shaft, SAE1030 carbon steel, 2-7/8 inches in diameter and 5 feet in length that is supporting a direct tensile load of 60,000 lbs, stress concentration factor K=1.47 and the yield strength is 40,000 psi? a. 2.9 b. 4.5 C. 3.4 d. 5.3 4. A bolt is subjected to an axial shock loading and the supplied load equals 12 kN. Assuming allowable stress of 55 MPa, determine the size of the bolt required. Use a stress concentration factor of 1.8. a. 18.67mm b. 26.67mm

3. What is the resulting factor of safety in a solid steel shaft, SAE1030 carbon steel, 2-7/8 inches in diameter and 5 feet in length that is supporting a direct tensile load of 60,000 lbs, stress concentration factor K=1.47 and the yield strength is 40,000 psi? a. 2.9 b. 4.5 C. 3.4 d. 5.3 4. A bolt is subjected to an axial shock loading and the supplied load equals 12 kN. Assuming allowable stress of 55 MPa, determine the size of the bolt required. Use a stress concentration factor of 1.8. a. 18.67mm b. 26.67mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
Q1) A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of Syt = 50 kpsi and Sye = 65 kpsi. Using the ductile Coulomb-Mohr theory, determine the factor of safety for the states of plane stress. 0x = 35 kpsi, and oy = 20 kpsi, Txy бу 0 Submit your answer in 4 significant digits. =
10. A steel bolt of diameter 10 mm passes through a brass tube of internal diameter 15 mm and external diameter 25 mm. The bolt is tightened by a nut so that the length of tube is reduced by 1.5 mm. If the temperature of the assembly is raised by 40°C, estimate the axial stresses the bolt and the tube before and after heating. Material properties for steel and brass are: Es=2x10' N/mm² a = 1.2x10 / C and E= 1×105 N/mm² α-1.9×10-¹5°C
1. A safety valve must start opening when the force is equal to 777.48N, and be fully open when (20mm spring compression) at a force of 812.82N. The spring should not be more than 90mm outside diameter, with the maximum shear stress under 1100MPA. The material used has a shear modulus of (G = 77.2 GPa). Determine the springs Mean Diameter, Wire diameter, Number of active coils and unloaded Length. D C = d 4С — 1 0.615 8FD Kw T = K,- nd³ + 4С — 4 C - 8FD³N y = 8FD³N dªG 1+ 2C² dªG
A right angle bracket arm experiences a downward normal force F(t) which cycles continuously between a minimum of 100 Lbs to a maximum of 400 Lbs. The machined part is made from 4140 steel, quenched & tempered at 800°F (Table A-21). Determine the factor of safety of the 5/8- inch diameter shaft at point A based on a life >10 million cycles using the DE - ASME-Elliptic Fatigue Failure Theory. Consider 90 % reliability and room temperatures. Assume stress concentrations, Kf = Kt = 1.7 and Kfs = Kts = 1.4 at point A. List governing equations and show all work.
Solve 5,6
Why does the answer of this problem consider radial stress if it is a thin walled?
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E -30,000 ksi, E-10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.
Machine design
An AISI 1035 CD steel tube has an OD = 45 mm and a wall thickness of 5 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 % of the minimum yield strength of the material? Assume ?? = 0.