3. A W300 x 67 has two lines of 20mm diameter bolts in each flange (three bolts in each line) which has a spacing as shown. A36 steel is used with Fy 250 MPa and Fu= 400 MPa. Compute the block shear strength of the section. The diameter of the bolt hole is 23mm. %3D Properties of W300 x 67 A=8,250 mm2 br=201.05 mm tr = 14.40 mm d= 300 mm tw = 8.4 mm -201.05 mm 32 mm 201.05 mm 300 mm 32mm

3. A W300 x 67 has two lines of 20mm diameter bolts in each flange (three bolts in each line) which has a spacing as shown. A36 steel is used with Fy 250 MPa and Fu= 400 MPa. Compute the block shear strength of the section. The diameter of the bolt hole is 23mm. %3D Properties of W300 x 67 A=8,250 mm2 br=201.05 mm tr = 14.40 mm d= 300 mm tw = 8.4 mm -201.05 mm 32 mm 201.05 mm 300 mm 32mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

WT12 x 38 Longitudinal welds Given: Properties of WT12 x 38: A, = 11.2 in? y = 3.0 in. b = 8.99in. Use A992 Steel: F, = 50 ksi F = 65 ksi LL = 3 DL %3D %3D tw = centroidal distance bf A. Governing Ultimate Tensile Capacity based on Yielding of gross section Round your answer to 0 decimal places.
Please double Check your final answer. Civil Engineering- Steel Design
1 please with explanation
Can u solve me step by step please . thank u
Internal effortsfeatures on a 750 mm sheet wide (made of ASTM A36 steel) were determined using a software basic structure analysis. The effort characteristic requester from a usage overhead is equal to 1260kN. Calculate the thickness needed for the plate? Adopt fyk = 250 MPa and fuk = 450 MPa.Please help Expert sir
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
Determine the allowable strength of the figure as shown
A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A В
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions