Answered: D=95k O O o O L = 9k PL ½x 8

Engineering

Civil Engineering

D=95k O O o O L = 9k PL ½x 8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate…

A: Given:- Thickness of plate, t=16 mmDiameter of bolts, d=22 mmNumber of bolts, n=6S1=40 mmS2=80…

Q: 60 b P P 150 100 100 100

Q: A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below.…

A: Answer We are given Plate 1/2 x 8 bolt diameter = 1 in A36 steel Shear lag factor U = 0.1

Q: The riveted type connection will be used to assemble the given steel members. If Parmar 6.25 t;…

A: Riveting is one of the methods to connect two metal pieces together. Rivets are the ductile metal…

Q: III. Calculation questions (1) s) A 300 × 10 mm plate of A36 steel is used as a tension member. The…

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

Q: A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm i…

A: Given data in question Shearing stress Torque Diameter To find out Additional number of bolts…

Q: A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa.…

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: bolted lap joint

Q: Found solutions, steel structure

Q: The area of the double angle shown is Ag = 5.6 in2. Each angle has a thickness t = 0.25 in. Given U…

A: Double Angle Tension Member Total Gross Area, Ag=5.6 in2 Thickness of angle, t=0.25 in Reduction…

Q: A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of…

Q: The details of an end bearing stiffener are shown in Figure . The stiffener plates are 9⁄16-inch…

A: A572 Grade 50:Fy=50 ksi Calculating the bearing strength: Apb=6-0.5×916×4=12.38 in2Rn=1.8 Fy Apb…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate Fy = 248 MPa Fu =…

Q: 2. The figure shows a plate having a width of 400mm and thickness of 12mm is to be connected to…

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: A W16x67 is given , we need to find out a. The nominal strength based on gross section yielding.b.…

Q: The angle shown in the figure is L 7 X4 X 7/16. Steel used is AS72 Gr. 55 steel. Diameter of bolts…

A: diameter of bolt = 1.125inch distance between two bolts=3inchs Ag=4,62in2 by steel table fy =70ksi…

Q: A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572…

A: Tensile capacity, the maximum load that a material can support without damage when being determined…

Q: A plate 400x12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter…

A: Given data Diameter of bolt (d) = 34 mm Diameter of hole (do) = 34 + 2 = 36 mm Width of plate (B)…

Q: 10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80…

Q: Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required…

A: Given, P =70 kNτ = 200 MPa

Q: Plate connection with bolts with shear strength value T=200 MPA is given in the figure. Determine…

A: It is required to determine the area of the bolt. T=PA Here T is the shear strength, P is the…

Q: Determine the maximum service load, P, that can be applied if the live load-to-dead load ratio is…

A: Solution:

Q: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

A: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: Bolted Connections hear lap connection

A: Single Shear Lap Connection: 22 mm bolts Fnv = 300 MPa Bolts are in Single Shear Number of bolts = 6…

Q: Please solve for the value of P

Q: The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58…

Q: The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in…

A: The values and diagram given in the question are as follows: Applied load(P)=5300 kN or 5300*103 N…

Q: Name the parts shown on the bolted joint element below, respectively. 3 Grip- washer - threads Head…

Q: For the tension member shown, compute the following. a. The tensile design strength. b. The…

Q: A. Governing Ultimate Tensile Capacity based on Yielding of gross section

A: This is one of the common types of forces transmitted in the structural system. The tension members…

Q: ckness of plate (1) is t = 18 mm. The ultim of the bolts is 320 MPa, and the ultimate of plate (1)…

Question

The tension member shown in Figure below is a PL 1⁄2 × 8 of A36 steel. The member is connected to a gusset plate with-11⁄8 inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = 0.85 An

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Please correct answer otherwise dislike
Determine the load capacity of the angle LRFD. USE NSCP 2015.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear