Course: Steel Structures please solve as your understaning A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for2-inch-diameter bolts. Assume that A, = 0.75A,.a. Determine the design tensile strength for LRFD.b. Determine the allowable strength for ASD.FIGURE 3.5Section2L5 x 3 x16 LLBB

Answered: Image /qna-images/answer/04c9123c-265a-4d45-89d8-adfca2e09eab.jpg

A double-angle shape is shown in Figure 3.5. The steel is A36, and th 4-inch-diameter bolts. Assume that A, = 0.75A,. a. Determine the design tensile strength for LRFD. b. Determine the allowable strength for ASD. FIGURE 3.5 Section 2L5 x 3 xVi6 LLBB

A double-angle shape is shown in Figure 3.5. The steel is A36, and th 4-inch-diameter bolts. Assume that A, = 0.75A,. a. Determine the design tensile strength for LRFD. b. Determine the allowable strength for ASD. FIGURE 3.5 Section 2L5 x 3 xVi6 LLBB

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.7P

See similar textbooks

Similar questions

Please answer number 1, please show all the solutions step by step.
Please answer
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Question 4 Complete the table below for the steel sections shown. All sections are bending about their horizontal axis. Section Location hep Ney Slenderness (show calculations) of element bf Flange te ld ++ tw be = 800 mm Web tf = 20 mm d = 1440 mm tw = 16 mm Grade 300, heavily 入。= Whole Asp= Asy= welded plates section br Flange tr d Web bf = 800 mm te = 20 mm d = 1420 mm tw = 16 mm Grade 300, heavily welded plates 入。= Whole Asp= Asy= section
PROB 2
ISA 100 x 100 x 10mm (Cross sectional area = 1908mm2) serves as tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm2 the tensile strength of the member can be taken to be approximately A ISA 100x100×10 Gusset Plate B
The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Asap pls
.