3) Determine the number of M24 Grade 10.9 bolts required to develop full yielding capacity of the UPN300 members. S275 Steel (Fy = 275MPa, Fu = 430MPa). Use LRFD provisions. Consider threads excluded from shear plane. Consider 3 columns of bolts (i.e., consider given spaces below) in the longitudinal direction. 25 mm thick plate UPN 300 50 O 50 mm 75 75 H

3) Determine the number of M24 Grade 10.9 bolts required to develop full yielding capacity of the UPN300 members. S275 Steel (Fy = 275MPa, Fu = 430MPa). Use LRFD provisions. Consider threads excluded from shear plane. Consider 3 columns of bolts (i.e., consider given spaces below) in the longitudinal direction. 25 mm thick plate UPN 300 50 O 50 mm 75 75 H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the LRFD design strength and the ASD allowable strength. Neglect block shear. A36 steel and 7/8-in Ø bolts N VA N SZ 2-MC 12 x 40 00 K All 2 in 2 in 3-in 3/in 2/in
A C12×30 is connected with 1-inch. diameter bolts in each flange, as shown in figure below. If Fy=50 ksi, Fa= 65 ksi and Ae=0.904 compute the following. a. The design strength for LRFD b. The design strength for ASD
Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown in the figure, Given that e= 30 mm, s= 50 mm, Fy =345 MPa and Fu=402 MPa, caicukato the following 2 L5 x3x % LLBD (two angles, long legs back-to-back) A242 stoel 60 mm e (am) (mn) e (mm) 55 Not area in shoar for a single angle under block shear lailue, Ariv mm? 56. Not area in tension for a single anglo under.block shoar failuto Arit = 57. Norninal block shear strongth in kN of the double angle Use Ups 10, Pn INPUT ALL ANSWERS AS WHOLE NUMBER
Expert Sir , Please solve my question Thanks in advance..
Please answer all the questions with a complete solution. thank you.
A double-angle shape, 2L7x4x3/8, is used as a tension member. The two angles are connected to a gusset plate with 7/8-inch-diameter bolts through the 7-inch legs, as shown in the figure 3. A572 Grade 50 steel is used. Compute the design strength and the allowable strength.
PL 5/8 x 12 3/4-in-diameter bolts
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
A C9x15 (A36 steel) with 2 lines of 3/4" diameter bolts in the webs as shown in the figure. Determine the LRFD and ASD strength in block shear failure.
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO