3) A 100-V rms, 60 Hz source is applied to a load impedance Z. The apparent power entering the load is120 VA at a power factor of 0.707 lagging.a) Calculate the complex powerb) Find the rms current supplied to the loadc) Determine Zd) Assuming that Z = R + jwL, find the values of R and L.

Given Data:Voltage (rms): Vrms=100V, Frequency f=60Hz. Apparent power: S=120VA Power factor:…

Answered: 3) A 100-V rms, 60 Hz source is applied…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Required information An ac motor with impedance ZL = (2.8 +1.60) Q is supplied by an RMS value of 220-V, 60-Hz source. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Find the power factor, the average power, and the reactive power. The power factor of the given ac motor is The average power of the given ac motor is The reactive power of the given ac motor is kW. KVAR.
Please help with d,e, and f.
The peak amplitude of the sinusoidal voltage source in the circuit shown in the figure is 180 V, a phase of 0 degrees, and its frequency is 5000 rad/s. a)Find VTH and ZTH for the thevenin equivalent circuit. b)Draw the thevenin circuit. c)Calculate the average power delivered to the load (between points a and b) when the load consists of a resistor and capacitor with RL=2000 0 and CL=0.2 uF. d)Determine the settings of RL and CL that will result in the most average power being transferred. e)What is the average power in (c)? Is it greater than the power in (a)? 6 kN 0.6 H a Vg 12 k2 9. +
Please help with the solution.
10. As the power factor of a circuit is increased, Reactive power is decreased Active power is decreased Reactive power is increased a. b. c. d. Both active and reactive power are increased 11. An RL series ac circuit has 15V across resistor and 20V across the inductor. The supply voltage is ___. a. 35V b. SV c. 25V d. √175 V 12. The power factor of the circuit shown in figure 1 is a. 0.8 lagging b. 0.75 lagging C. 0.4 lagging d. 0.6 lagging
I need help with this homework question.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
Pls. write solution neatly
please solve each part thank you i will like

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning