29. Figure shows the line drawing of a residential building, draw to a scale of the following, (a) Plan (b) Sectional elevation along AA first Cement concrete base 300 mm thick and 900 mm wide is provided under main walls. Footings are brick wall in CM 1:6, 600 mm wide and 300 mm deep depth to which main walls are taken below the ground level is 1000 mm. Supers structure: Main walls 300 mm thick and other 200 mm thick. Head room 300 mm, Assume suitable footings below verandah. Roofing : 1:2:4 RCC slab 120 mm thick Any other data not furnished may be suitably assumed. Store Kitchen Bed room 2x3 3 x 3 3. 3 x 4 Toilet 3 x 2 Dinning 4x3 3D Drawing 5 x 4 All dimension are in mm Figure Verandahi 2x4

29. Figure shows the line drawing of a residential building, draw to a scale of the following, (a) Plan (b) Sectional elevation along AA first Cement concrete base 300 mm thick and 900 mm wide is provided under main walls. Footings are brick wall in CM 1:6, 600 mm wide and 300 mm deep depth to which main walls are taken below the ground level is 1000 mm. Supers structure: Main walls 300 mm thick and other 200 mm thick. Head room 300 mm, Assume suitable footings below verandah. Roofing : 1:2:4 RCC slab 120 mm thick Any other data not furnished may be suitably assumed. Store Kitchen Bed room 2x3 3 x 3 3. 3 x 4 Toilet 3 x 2 Dinning 4x3 3D Drawing 5 x 4 All dimension are in mm Figure Verandahi 2x4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to Figure P2.4 for the floor plan. Calculatethe tributary areas for (a) floor beam B3, (b) floor beamB4, (c) girder G3, (d) girder G4, (e) edge column C3, and(f) corner column C4.
2/ For the plan (hexagon shape) and section of the wall shown in No. 1. Calculate quantities for each of the following construction works: 1- Excavation works for foundation. 2- Brick works (under & above the D.P.C level up to the parapet wall). Each line in the room is 3m length from inside Plan W1 1.5m 60 W1 D Width (m) 1 Height (m) 2 W1 2 1.5
Figures below show the typical floor framing plan and sections of a three-story reinforced concrete building. Weight of concrete= 150 pcf, f'c = 4000 psi, fy = 60,000 psi. Using ACI Code 318-19: Assuming single slab depth is used throughout, what is the minimum slab thickness required for deflection control for the typical floor? all 25' 25 Col. size 10x10 Typ 25 == 14 X- Typical Floor Framing Plan 45-24 12°~0° + 10:0° + 10-0² t #3 Serp +10° to Sec. 1-1 Sec. X-X
underneath determine is the plan and section of a R.C. slab 13 cm thick overalls resting on 30cm partitions cantilevered out on one facet. The slab is bolstered bothways, a, b, c, m and n all are 12mm dia. bars. put together a time table of bars for the slab assuming weight of 12mm and 10mm dia. bars are as 089 kg and 062 kg respectively. expect 12mm clear cowl. acm 30cm 19 CRANKED PART CRANKED PART 1300-6501-1 Hwas 12 BAB 25 E 2cm3 CH FEMAL 25 a -4.5 M 54CM TaeECHI C/C Laxb@.ocne/c Approducat 30 GRANKED PART -112m2 [-be20cm c/c & 12cme/cce verje 30 54cm-12m-30 SECTION ON A A ·PESHT 15M 13,523011 bac^icmcfe 1.5M- 10-ma25cc TOP BARS FOR CANTILEVE FOR CANTILESLY SLAD CHLY CANTILEVER DISTRIBUTION Ens SLAB Vimma @250: c/c -1.45M * IS
A 50-m steel has an error of 0.02 m at 20°C with a pull of 50 N. A rectangular lot is to be staked out using this tape. The sides are 24.63 m and 10.65 m. The average temperature of the tape during staking out is 20°C with a pull of 50 N. The laid out area of the lot in square meters is: NOTE: Units are not required. Round-off to two decimal places.
Given: Footing Column Required: Steel Works by Direct Count Method 0.35x0.35x4.00 Column with 6-D20mm Column RSB D10mm Lateral Ties @ 0.15m O.C. -1.50x1.50x0.50m Footing with D20mm @ 0.10m O.C. BW
Estimate the quantity of cement bags, sand and gravel in cubic meter, and water in gallons per floor level sections. A. Substructure (including footings) and ground floor Beams Columns Slab Note: Above the roof deck, steel railings will be used at the perimeter of the building; no masonry work at this part. Only concrete columns extending from the second floor. Bathroom is 2.8 meter by 4 meter. Itemize quantities per floor level using the format below: A. Exterior Walls (six inches thickness) CHB Fill Block Laying Rough Plaster (both sides 3/4in) Smooth Plaster (both sides) B. Interior Walls (four inches thickness) CHB Fill Block Laying Rough Plaster (both sides 3/4in) Smooth Plaster (both sides)
How does the assumption of ''plane sections remain plane" simplify the calculation of the maximum possible depth of the neutral axis,x? By making an appropriate drawing, calculate the maximum possible value of x for a reinforced concrete section which has concrete class <= C50/60 and steel S500. Explain why EC2 apply this limitation (i.e., x<=0.45d).
H.W.5: Determine the design moment strength of a rectangular concrete section reinforced with six no. 9 bars in two rows. Given : b 305 mm, d 622 mm, total depth h- 686 mm, and reinforced with three no. 9 bars, fy = 414 MPa and f. = 27.58 MPa. 27 6 # 9 305 mm 686 mm 622 mm
Problem 01. Analyze the building frame shown using Portal Method.