Given an 8" wide x 100' long x 6' tall (above the footing) concrete block fence with #5 vertical bars @ 8'-0" o.c. and an 8" x 8" with 1 - #5 bar Tie Beam, calculate the following: (Neglect the footing concrete and the footing steel reinforcing.) How much concrete is required for the vertical "drops" and horizontal tie

Given an 8" wide x 100' long x 6' tall (above the footing) concrete block fence with #5 vertical bars @ 8'-0" o.c. and an 8" x 8" with 1 - #5 bar Tie Beam, calculate the following: (Neglect the footing concrete and the footing steel reinforcing.) How much concrete is required for the vertical "drops" and horizontal tie

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4) If the coefficient of resistance, R, has been found to be 410 psi for a solid one-way slab of 4 ksi concrete and 40 ksi steel, what reinforcement ratio, p, would you select to find an area of flexural reinforcement in order to choose the appropriate number and bar sizes for design? ? What would the area of steel, As, per foot of width be for that ratio when d = 7.5 in.?
Sketch the different types of Shallow footings showing the main reinforcement and secondary reinforcement directions.
Calculate the weight of a Wire Mesh Reinforcement needed for a 10'x10' slab. The specifications are requiring the use of WWF3x2xW2.9xW1.4
What are Continuous spread footings
As a Consulting Professional Engineer, you are required to provide a complete detailed structural design/analysis for the R.C. Wall specified in the following project problem under the "NEW" Loadings condition, and the new section-as specified below: "Design the reinforced concrete wall shown if fc' = 4000 psi and fy = 60,000 psi". %3D By changing the Horizontal Load to 200K, H=14 ft and L=14ft. 10 in. V, = 300 k h, = 12 ft 0 in. lw = 12 ft 0 in.
Explain about strap footing with neat drawing.
2. Draw the elevation of an isolated footing column and pier detail: 250 mm x 300 mm RC column having a 150 mm x 150 mm wood post with 2-6 x 50 x 600 mm post strap on 16 mm bolts and a footing with a size of 1200 x 1100 mm with #16 tie wire.
please answer asap thank u
Using the drawings for Billy’s Convenience Store, in Appendix F, the quantity of concrete and reinforcing steel required for the spread footings.
15. A contractor is building thirty-two (32) of the 2'- 0"x 2'- 0"x 0"-10" spread footings shown in the drawing below. Using the material schedule at the bottom of the page, answer the questions a to f below. Concrete (cy) • Rebar (lbs) 2 x 12 Forms 2 x 4 stakes (each) • Nails (lbs) "x12" CF Plan View 2-37 Side View (2) #4 brach way top and botto ▲ Section A-A Concre "x12" Concrete Farm 2"x4" 2-6 Side View Material Specification Frequency Waste, of Use % Concrete 4,000 psi 1 3 Rebar # 4 (0.668 lbs/lf) 1 10 Forms 2 x 12 in. x length 4 10 Stakes Oak, 2 x 4 x 18 in. 4 25 Nails 3½ in. common 1 10 2-67 2x 12" Conte Form 4x4 Sales Concrete (2) reach way top and bott 2-3 Section A-A Comments Use exact measurements then add waste 2" clearance from ends to forms Use exact measurements then add waste Total length is 18" 1 lb/100 bf of total lumber (forms plus stakes)
Question 8 A sample slab section view is shown below: *4 0 10" EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab? What should be the correct reinforcement configuration in plan view for this slab? 10" 10" 10" 10"- #4 bars 10"- 10" 10" 10" #4 bars 10"- # 4 bars 10"-