Q19. Figure shows the line drawing of a residential building draw to a scale of the following, (a) Plan (b) Section along AB (c) Front elevation The following specification are to be adapted foundation: Depth 1000 mm, CC bed 1000 mm x 300 mm, two footings with an offset of 50 mm and 250 mm thickness each. Basement: 600 mm high, Thickness of wall at this level is 400 mm Walls : Brick masonry in CM : 1:6, 300 mm thick Roof : RCC slab 120 mm thick, provide doors, windows, ventilators, steps etc., as per standard dimensions, assume any data required. A W Kitchen and Bed room dinning W W 4500 x 4500 iD D 4000 x 4000 Toilet V Living room 4000 x 1000 2000 x 2000 ! W Bed room W 4000 x 4000 D Verandah W 2000 wide Figure

Q19. Figure shows the line drawing of a residential building draw to a scale of the following, (a) Plan (b) Section along AB (c) Front elevation The following specification are to be adapted foundation: Depth 1000 mm, CC bed 1000 mm x 300 mm, two footings with an offset of 50 mm and 250 mm thickness each. Basement: 600 mm high, Thickness of wall at this level is 400 mm Walls : Brick masonry in CM : 1:6, 300 mm thick Roof : RCC slab 120 mm thick, provide doors, windows, ventilators, steps etc., as per standard dimensions, assume any data required. A W Kitchen and Bed room dinning W W 4500 x 4500 iD D 4000 x 4000 Toilet V Living room 4000 x 1000 2000 x 2000 ! W Bed room W 4000 x 4000 D Verandah W 2000 wide Figure

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explain about strap footing with neat drawing.
What is the centerline perimeter of the footing shown on plan? 40'-0" Footing width=2'-6" 25'-0" 140 ft 120 ft 130 ft 110 ft
What are ring spread footings ?
Given sketches of various structural foundation section details, properly identify and label the building components.
Why is the sum of un factored load instead of the factored load used for determining the width of the footing?
Design Criteria: fc' = 27.6 MPa, fy = 414 MPa, Perimeter Walls (Grid 1, Grid 7, Grid F) 0.72 KPa, Floor finish = 1.5 KPa, and LL = 2.4 KPa. Design B1,B2, B3, C1, C2, C3, S1, S2, and S3.
Figures below show the typical floor framing plan and sections of a three-story reinforced concrete building. Weight of concrete= 150 pcf, f'c = 4000 psi, fy = 60,000 psi. Using ACI Code 318-19: Assuming single slab depth is used throughout, what is the minimum slab thickness required for deflection control for the typical floor? all 25' 25 Col. size 10x10 Typ 25 == 14 X- Typical Floor Framing Plan 45-24 12°~0° + 10:0° + 10-0² t #3 Serp +10° to Sec. 1-1 Sec. X-X
Using the drawings for Billy’s Convenience Store, in Appendix F, the quantity of concrete and reinforcing steel required for the spread footings.
15. A contractor is building thirty-two (32) of the 2'- 0"x 2'- 0"x 0"-10" spread footings shown in the drawing below. Using the material schedule at the bottom of the page, answer the questions a to f below. Concrete (cy) • Rebar (lbs) 2 x 12 Forms 2 x 4 stakes (each) • Nails (lbs) "x12" CF Plan View 2-37 Side View (2) #4 brach way top and botto ▲ Section A-A Concre "x12" Concrete Farm 2"x4" 2-6 Side View Material Specification Frequency Waste, of Use % Concrete 4,000 psi 1 3 Rebar # 4 (0.668 lbs/lf) 1 10 Forms 2 x 12 in. x length 4 10 Stakes Oak, 2 x 4 x 18 in. 4 25 Nails 3½ in. common 1 10 2-67 2x 12" Conte Form 4x4 Sales Concrete (2) reach way top and bott 2-3 Section A-A Comments Use exact measurements then add waste 2" clearance from ends to forms Use exact measurements then add waste Total length is 18" 1 lb/100 bf of total lumber (forms plus stakes)
You are assigned the foundation design of a 56'-0" inside diameter reinforced concrete process tank. Vertical walls are 1'-0" thick and 15 feet high, terminating at elevation 25.00. Bottom of wall is at elevation 10.00 and rests on the foundation slab. Exterior grade abutting the vertical tank walls is at elevation 22.00. The tank foundation slab is circular with a two foot extension all around the vertical tank exterior wall. Determine the minimum height of the foundational circular slab. For design purposes consider the groundwater to be saturated to sit grade. Determine the following: A) Buoyant force in pounds B) Minimum depth of foundation slab in feet
9.9 Refer to the following photographs of concrete wall cracking. Indicate which case is likely caused by foundation settlement, seismic shear, loading retaining wall pressure. IBMB b)