27. Determine the amount of excavation and backfill needed for the basement presented below. 30-0 26-0¹ -30-0 -26-0 -40-0- 50-0 Foundation Plan Answer: (1) Excavation: (2) Backfill: -50 5'0" L1'-6" IM 26-0- -28-0- -30-0- 40-0 -50-0- Section 11'0" 10% BCY CCY BE 10-0 L

27. Determine the amount of excavation and backfill needed for the basement presented below. 30-0 26-0¹ -30-0 -26-0 -40-0- 50-0 Foundation Plan Answer: (1) Excavation: (2) Backfill: -50 5'0" L1'-6" IM 26-0- -28-0- -30-0- 40-0 -50-0- Section 11'0" 10% BCY CCY BE 10-0 L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the quantity of earthwork for a cement concrete road 200m length for a portion of road in…

A: Length of road, height of bank from one end, height of bank from other end, Formation width,

Q: 1.State the uses of sheet pile wall? 2. Listthe advantage of sheet piling over other retaining…

A: 1.to retain walls constructed to retain earth, water or any other filling materials2.Water front…

Q: B AS-1 14 A A AS-2 TYPICAL FOOTING PLAN SCHEDULE OF FOOTING SIZES & REINFORCEMENT FOOTING SECTION…

Q: b2: Prepare measurement sheet for the following items of works using drawing of boundary wall given…

A: Hi! Thank you for the question, As per the honour code, we are allowed to answer three sub-parts at…

Q: 9- Consider the following operations in Bridge shallow foundation construction: 1. Placing steel 2.…

A: Shallow foundations disperse impact load throughout vast regions of near-surface topsoil to reduce…

Q: Using a waste factor of 7 percent, determine the number of cubic yards of concrete needed to pour…

Q: Find the plan dimensions of the footing.

A: Load on column 1 is W1 = 600+450 = 1050 KLoad on column 2 is W2 = 400+300 =700 KLoad on column 3 is…

Q: The detail drawings of the concrete footings for a building are shown below. The bars to be ordered…

A: Data given Bars to be ordered = 16 mm ϕ × 6 m Value to be calculated for =15 footings Footing…

Q: QUESTION 4 What is the type of the embedded retaining wall shown in figure? Refer to 02 Installation…

A: (c) is the correct answer.

Q: PROBLEM 1 -Given the following sections 1+020 a +0.90 +3.5 +0.55 1+080 -1.85 -1.20 -0.42 Base for…

A: Given, FILL: Base for fill= 12 m side-slope = 1:1 CUT: Base for cut= 12 m side-slope = 2:1 Distance…

Q: Question 1 of 8 5F Determine the number of 6meters - 12mm. steel bars required if there are 10…

A: Since the spacing between the bars are not given then from the drawing, number of bars are counted.…

Q: 8 - Foundations considered as deep when a) Depth /width >2.5 b) Depth /width 5 d) Depth /width<10

A: The foundations are mainly of two types. Shallow foundation Deep foundation. The foundation is…

Q: Design the largest interior and edge panel of the slab for the plan system shown below (Follow the…

Q: Base for cut = 12 m, Sideslope for cut = 2:1 Base for fill = 12 m, Sideslope for fill = 1:1…

A: Excavation : The movements of ground, rock, or other materials using tools, machinery, trenching,…

Q: 6.3 Refer to Figure 6.7 and consider a rectangular foundation. Given: B = 1.5 m, L=2.5 m, Df = 1.2…

A: Since you have posted multiple questions, we will provide the solution only for the first question…

Q: Question 12 The top width of excavation is: (1 4.05 m 2) 6.40 m 3 4.30 m None of the answers are…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: 50'-0" 25'-0" C. 2'-6" Footing cross section -6 a. THREE DIMENSIONS: If this slab has a continuous…

Q: Compute the A) analysis of loads B)total downward load and C) base area of the footing

A: Given: Dead loads Live loads Cross-section of square footing =…

Q: 5. Determine whether the slabs shown is a two-way or one-way and also 3m S-1 approximately find the…

Q: a continuous footing installed at a depth of 2 feet with a base of 5 feet wide is constructed on the…

A: Df = 2 ft B = 5 ft γ = 120 pcf ϕ' = 35o

Q: In the following photo, identify the type of footing that is being installed. Photo A: Photo A:…

A: Given data in question Foundation site picture To find out Which type of Foundation is this

Q: SHOW FIGURE Given the following sections: Station 2 + 020 a 0 b +2.5 +3.15 +2.65 Station 2 + 080…

Q: State THREE (3) excavation works involve in pad footing construction. 1. Excavation for......... 2.…

Q: Q4: From the given figure below calculate the detailed and abstract estimate for the double roomed…

A: DETAILED ESTIMATE S.NO DESCRIPTION UNIT NOS NOS L…

Q: 1. An excavation is to be made for a footing 1.5 m x 1.5 m. However during the excavation you…

A: We need to first dewater the pit which is not possible at instance as water is getting accumulated…

Q: Define the Foundations in Granular Soil (c' = 0) ?

A: Where the sub-base contains gravel and dirt, combined footing and strap foundations are the best…

Q: A combined footing carries two columns with the following information: The edge of the left column…

Q: Q2) For the column layout shown in Figure (2), find the plan dimensions of a combined footing and…

A: Solution; The values provided in the question are as follows: Soil allowable bearing capacity…

Q: Question 52 What is the MAXIMUM elevation variation of anchor rod tops from the foundation? 1. 1 2…

A: In the design of Column base plate, there are variations arise due it's construction in Anchor bolt…

Q: Shown here is the cross-sectional detail of footing and dimensions are in millimeters. These are 12…

A: The dimensions of one footing are:- Length=2.7m Breadth=2.7m Height=1500mm=1.5m Volume of excavation…

Q: Problem 2: Find the Area and volume of the footings shown below. Use the center line method to…

A: The total length of the center line of the wall should be determined.Then the area of the footings…

Q: Describe about the shell-less pile.

A: Shell: The shell is basically made of corrugated and reinforced thin sheet steel or pipes. A steel…

Q: e advantages and disadvantages of using sheet pile coffer

A: This question has been taken from geo technical engineering.

Q: 2.15m-2.15m2.15m2.15m2.15m2.15m 8 8 -1.25

A: Given:- concrete piles -450 X 450 mmm C1-1800 X 2000 mm C2-1600 X 2000mm To find:- total volume…

Q: If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column…

A: Compaction: The reduction of air voids from the tightly packed soil particles is known as…

Q: Write a note on - Design Procedure of strip footing ?

A: The answer is below:

Q: OK, now we have to deal with the spoils. Assume the Finished Grade (FG) was level and all one…

A: Given Finished grade was level No slope Using minimum OSHA offset it is 2 Ft so…

Q: If a footing labeled as F-3 (ocurring 5 times on the foundation plan) is described by the following…

Q: Which is false of the following prestress loss combination ?

A: its not mentioned in question what is σ

Q: A partial-diaphram type of earth embankments is sometimes referred to:

A: An embankment dam is an artificial dam that is constructed of natural materials. There are two types…

Q: Define Terzaghi-Peck Charts for Backfill Pressures.

A: For gravitational and I and T shape RCC retaining walls, Terzaghi & Peck (1967) have developed…

Q: What would be the amount of concrete in cubic yards required for the footing below assuming a depth…

A: length of footing is

Q: Q1/ For the plan shown below; determine quantity of foundation only for masonry in cement mortar…

Q: An excavation is to be made for a footing 1.5 m x 1.5 m. However during the excavation you…

A: Footing is the subgrade of the structure which is very useful to transfer the load and also to give…

Concept explainers

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.

Question

7. Determine the amount of excavation and backfill needed for the basement presented below.
30-0 26:0¹
-30-0-
-26-0
-400-
50-0'
Foundation Plan
Answer: (1) Excavation:
(2) Backfill:
-540¹
5'0'
L1'-6"
IM
-26-0
-28-0
30-0
-40-0
-50-0-
Section
11'0'
1-0%
BCY
CCY
10-0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 : Introduction

VIEW

Step 2 Calculation of Amount of Excavation and Backfill

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Measuring sitework, excavation and piling

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Why is timportant to: ▪ Protect the depth of excavation against cave-ins.▪ Keep the horizontal width of the excavation to make sure that work activitywould not vibrate the soil while workers are in the trench.▪ Plan the foundation work to minimize the number of workers in the trench and the length of time they spend there.▪ Inspect the trench regularly for changes in the stability of the earth (water,cracks, vibrations, spoils pile).▪ Stop work if any potential for cave-in develops and fix the problem beforework starts again.
Given ten (10) units of isolated rectangular footing, 1.20m x 2.00m x 0.30m, reinforced with 10pcs -12mm diameter bars along the 1.20m dimension and 6pcs - 12mm diameter bars along the 2m dimension, (Structural Grade rebar). The depth of excavation is 2m below the natural ground and the soil is sandy loam. Use Class A concrete mixture and concrete cover of 75mm. Assume no wastage. Make a Bid Price in BOQ format. How much is your bid amount? * Subject: Construction Methods
Draw the figure.
22¹ Determine the amount of excavation needed for the basement shown in the figures. A two-foot working distance is required, and the excavation will be sloped 1:1.75 (1.75 Vertical to every 1 foot horizontal) Basement Plan View. 34' 8' 2'-6"
Please answer Problem no 2 **********
Q4: For flexible footing shown below, find the immediate surface settlement below the point a. dq 200 kPa, -0.5, E 22800 kPa S - " (1-, Use l, 0.76
Determine the reinforcements for given slab systems and draw a sketch to show bar arrangements 44 + -12 cm 3.25 1.50 h=120 mm Q=2.0 kN/m² (for Slabs) Q=5.0 kN/m² (for Balcony) -12 cm 3.35 1.50 0.25 ++ + =12 cm 325 150 0.25 ++ + 12 cm 3.25 3.50 Yconcrete 25 kN/m³ Coverage+plaster= 1.5 kN/m² Materials: C25/S420
Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate the steel reinforcing bars required if the length of the bars to be ordered is 6.060 meters. 0.60M COLUMN 1.20M PLAN OF FOOTING 3-Ø16MM BARS 6-Ø12MM BARS FOOTING COLUMN BARS COLUMN COLUMN TIES 3-Ø16MM BARS 6-Ø12MM BARS (TYPICAL) 0.30M www. w SECTION OF FOOTING
1) Design a rectangular footing for an 16” square corner Column with PDL = 280 kips and PLL = 180 Kips. Make the length of the long side about 1.5 the width of the short side. Fy = 60 ksi F’o= 4000 psi for both, column and footing. Assume the base of the footing is 4'-6" below grade and the depth of the footing is 26". The soil weight is 100 PCF. (Normal weight concrete, No epoxy coating, The Column is reinforced with eight #8 bars.) Need to design for load transfer from the Column to the foating. Need to Show the development length for the dowels. Need to design the bars for footing at both directions. Need to check if the bars fit the footing based on the development legth. Need to show two-way footing Spacing diagram.
1. The height of excavation is 1.30m 2. Soil type: fairly good soil.
15. A contractor is building thirty-two (32) of the 2'- 0"x 2'- 0"x 0"-10" spread footings shown in the drawing below. Using the material schedule at the bottom of the page, answer the questions a to f below. Concrete (cy) • Rebar (lbs) 2 x 12 Forms 2 x 4 stakes (each) • Nails (lbs) "x12" CF Plan View 2-37 Side View (2) #4 brach way top and botto ▲ Section A-A Concre "x12" Concrete Farm 2"x4" 2-6 Side View Material Specification Frequency Waste, of Use % Concrete 4,000 psi 1 3 Rebar # 4 (0.668 lbs/lf) 1 10 Forms 2 x 12 in. x length 4 10 Stakes Oak, 2 x 4 x 18 in. 4 25 Nails 3½ in. common 1 10 2-67 2x 12" Conte Form 4x4 Sales Concrete (2) reach way top and bott 2-3 Section A-A Comments Use exact measurements then add waste 2" clearance from ends to forms Use exact measurements then add waste Total length is 18" 1 lb/100 bf of total lumber (forms plus stakes)
If the post is to be erected in a medium clay [maximum soil bear capacity is 250 kPa], and will be placed on top of a square footing weighing 25 kN, what will be the minimum dimension of the footing?