Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate the steel reinforcing bars required if the length of the bars to be ordered is 6.060 meters. 0.60M COLUMN tumb 1.20M PLAN OF FOOTING 3-Ø16MM BARS 6-012MM BARS FOOTING COLUMN COLUMN BARS COLUMN TIES 6-012MM BARS (TYPICAL) 3-Ø16MM BARS purup SECTION OF FOOTING

Q: #5 DOWELS @ 12" O.C. ALTERNATING DIRECTIONS #4 REBAR @ 12" O.C. 5 EACH #4 CONT. REBAR 3' 1'-3" 12'…

A: Given Data, Continuous bar = 5 each #4 Lateral bar = #4 @ 12 inch on center Dowel bar = #5 @ 12 inch…

Q: In the following photo, identify the type of footing that is being installed. Photo C: Photo C:…

A: Given data in question  Footing picture To find out  Which type of footing is given in picture

Q: The figure shows the outside dimensions of a building perimeter wall. a) Calculate perimeter of the…

A: Given dimensions of a building thickness of wall = 48 – 15x2 = 18” = 1.5 ftproject of footing on…

Q: 3. Calculate the total load on a 4'x4'x1' spread footing that is buried 3' below, and a hot tub is…

A:

Q: 4'-0" Nominal 5.25"- 5 @7.5" = 3'-1.5" 5.25" € 5.25" Voids 2" Topping 1.13" 1.75" 5.75" 1.13" 1.75"…

A:

Q: 7. The rebar is to be lapped 18 inches.

A: Show the footing plan as in Figure (5-26) Show the footing plan as in Figure (5-27) Show the…

Q: Using a waste factor of 7 percent, determine the number of cubic yards of concrete needed to pour…

A:

Q: B. True-False Questions 1. Because it is so low in density, aluminum does not conduct heat well. ( )…

A: Answer b) 1)  Because it is so low in density, aluminum does not conduct heat well. This statement…

Q: Submit the following online or on paper: The footing below is a 5ft square. The soil immediately…

A: The unit weight of the soil above the footing, The unit weight of the soil below the footing, The…

Q: Calculate punching capacity of the given footing 8'x6' supporting 14"x14" column. The thickness of…

A:

Q: In the following photo, identify the type of footing that is being installed. Photo D: Photo D:…

A: Given data in question  Footing picture To find out  What type of footing is used there

Q: A bill of quantities is to be prepared for the square isolated reinforce column and footing as…

A:

Q: rom the face of the foundation footing the above N 10 -15M rebar in a continuous concret

A: ANS (11) TRUE

Q: Trade Production Number Hourly Activity Unit Name of Rates Duration Output workers in Crew ($)…

A: Table Activity Unit Name No of workers in crew hourly rate Duration (hour) Output (unit)…

Q: Define Equivalent Uniformly Loaded Footing

A: Footings are a very important part of the foundation. They are constructed with the help of concrete…

Q: A column load (force) of 33 kip acts on a square footing. Calculate the size of the footing if the…

A: Given data,square footingcolumn load=33 kippressure on soil=1 kip/ft2depth of aggregate is 8…

Q: Problem 2: Find the Area and volume of the footings shown below. Use the center line method to…

A: The total length of the center line of the wall should be determined.Then the area of the footings…

Q: In the following photo, identify the type of footing that is being installed. Photo B: Photo B:…

A: To find which type of fitting is shown in figure-

Q: The figure shows a cast-in-place reinforced concrete spread footing for an interior column that is…

A:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.